manualshive.com logo in svg

Nordson 1006453A, Руководство пользователя по изделию, Страница: 22 / 24

Поделиться
Скачать
Nordson 1006453A Скачать руководство пользователя страница 22

Ejector Gun Controller

18

E

2001 Nordson Corporation

All rights reserved

1006453A

Issued 6/01

Manual 25-23

Follow these procedures to replace the power cable that connects the
keypad to the PLC.

See Figure 4.

1. Disconnect power at the knife disconnect and open the controller

door.

2. Unplug the communication cable (6) from the keypad (1).

3. Unplug the communication cable from the PLC (7).

4. Plug a new cable into the PLC and the keypad.

5. Close the controller door and restore the power connection at the

knife disconnect.

Follow these procedures to replace the PLC in the Ejector gun controller
enclosure.

See Figure 4.

1. Disconnect power at the knife disconnect and open the controller

door.

2. Disconnect the wires and communication cable (6) from the PLC (7).

3. Disconnect the PLC from the DIN rail and remove the PLC from the

controller enclosure.

4. Install the new PLC onto the DIN rail.

5. Connect the wires.

6. Download the most current Ejector gun program according to your

programming software literature, using the cables supplied for
downloading.

7. Put the PLC in the software RUN mode.

8. Plug in the communication cable.

9. Close the controller door and restore the power connection at the

knife disconnect.

Replacing the
Communication Cable

Replacing the PLC

Содержание 1006453A

























Отзывы:

Нет отзывов