Nordpeis N-20 T, Руководство пользователя, Страница: 5 / 48

Front frame FIG 6
Assemble frame to the insert body with provided screws
and tools as shown on the drawing. Pay attention to
correct postion of air lath and the air valve handle.
Ignition air handle FIG 7
Before assembling the handle screw in the fastening
pins. When ignition handle in place check several times
if it is kept on position, work properly and smoothly.
Back frame FIG 8
Assemble back frame with fasteners and tools provided.
Assembling heat shields FIG 9 - FIG 11
1. Assemble side covers on insert pins as shown on
drawing FIG 9.
2. Place a rear top cover. Check on both sides FIG 10b
and on a frame FIG 10c correct postion.
3. Asseble a front top cover. Pay attention to proper
overlapping of sides FIG 11a & b.
4. When all cover are in place join it toghether by provi -
ded screws - FIG 11c.
Door assembling & Self closing door mechanism
FIG 12 - FIG 15
In some countries self-closing door mechanism is obli-
gatory by law.
Attention: If you deavtivate the system where is obliga-
tory you risk serious conseqenses enforced by local law.
Attention:
If in your country it is not required you can
desactivate it.
Deactivation & Door assembling FIG 12 - FIG 15
The insert doors are provided with tensioned door
springs. Unscrew fastener as shown on FIG 12,
when you hear a noise the mechanism is deactivated.
To assemble door follow steps shown on drawing
FIG 13 - FIG 15.
Door assembling & Activation FIG 13 - FIG 15
Assemble the door as shown on drawings. When
the door is on it’s place unscrew the fastener and
realease tensioned spring. Now, the mechanism
is activated.
Attention: The same procedure is applicable to back
door assembling.
Attention: The door can be deinstalled by following
the same steps in reverse order.
Multipurpose key
The insert is equipped with an handle, which is intended
for operating, ie.: air vents, opening and closing doors -
see FIG 16 - FIG 19 .
Operational control
When the insert is in upright position, and
prior
to mounting the surround,
control that all functions
are easy to maneuver and appear satisfactory.
A. Ignition vent control B. Air vent control
Pushed in = closed
Pull out = open
Left position = closed
Right position = open
5. Lighting a fire for the first time
When the insert is assembled and all instructions have
been observed, a fire can be lit.
Take care when inserting logs into the burn chamber, in
order not to damage the Thermotte plates.
This will be resolved once the humidity has evaporated.
If needed leave the door slightly open the first 2-3 times
the insert is used.
It is advisable to ventilate the room well when using
for the first time as the varnish on the product may
release some smoke or smell
. Both the smoke and
smell will disappear and are not hazardous.
Warning!
In order to avoid injuries, please be aware that the
surfaface may become hot during operation and
extra care need to be taken to avoid skin burn.
Lighting a fire
Kindling wood
Finely chopped (diameter of 3-5cm)
Length: 25-30cm
Ca. amount pr lighting : 2 kg
Place the air vent control in ignition (FIG A) (Pull out).
Insert small, dry pieces of wood, ignite and ensure the
flames have taken proper hold of the wood. When the
flames are stable and the chimney is warm, push in the
air control out of the ignition mode and regulate the fire
normally.
When there is a glowing layer of ash, new wood logs
can be inserted. Pull the hot ember to the sides of
the combustion chamber when inserting new logs so
that the wood is ignited from the bottom. Insert 2 logs
positioned pararelly to the glass door. The fire should
burn with bright and lively flames.
Reload size
Chopped wood (diametre of 6-9cm)
Length: 25-30cm
Normal load size. 1,55 kg /h
(Max load size: 2 kg/h)
FIG A FIG B
5
GB