Nordpeis 22-Q23FL-000, Руководство пользователя, Страница: 8 / 30

23
GB
6RPHDGYLFHLQFD se of combustion problems
Error Explanation Solution
1RGUDXJKW
The chimney is blocked.
Contact a chimney sweeper / dealer for more information or clean the
ÀXHVPRNHEDႉHDQGEXUQFKDPEHU
7KHÀXHLVVRRW\RUWKHUHLVDFFXPXODWHGVRRWRQWKH
VPRNHEDႉH
7KHVPRNHEDႉHLVZURQJO\SRVLWLRQHG 9HULI\WKHDVVHPEO\RIWKHVPRNHEDႉHVHHDVVHPEO\LQVWUXFWLRQV
The insert
release smoke
ZKHQOLJKWLQJ
WKH¿UHDQG
GXULQJFRPEXV
-
tion
Downdraught in the room caused by no draught, that the
house is too “air tight”. /LJKWWKH¿UHZLWKDQRSHQZLQGRZ,IWKLVKHOSVPRUHELJJHUYHQWVPXVW
be installed in the room.
Downdraught in the room – caused by extractor and/or
central ventilation system that pulls too much air out of
the room.
7XUQRႇUHJXODWHH[WUDFWRUDQGRURWKHUYHQWLODWLRQ,IWKLVKHOSVPRUH
vents must be installed.
7KHÀXHVIURPWZR¿UHSODFHVVWRYHVDUHFRQQHFWHGWR
the same chimney at the same height.
2QHÀXHPXVWEHUHSRVLWLRQHG7KHKHLJKWGLႇHUHQFHRIWKHWZRÀXH
pipes must be of at least 30 cm.
7KHÀXHLVLQDGHFOLQLQJSRVLWLRQIURPWKHVPRNHGRPH
to the chimney.
7KHÀXHPXVWEHPRYHGVRWKDWWKHUHLVDQLQFOLQDWLRQRIDWOHDVWž
from smoke dome to chimney. Possibly install a smoke suction device*.
7KHÀXHLVWRRIDULQWRWKHFKLPQH\
7KHÀXHPXVWEHUHFRQQHFWHGVRWKDWLWGRHVQRWHQWHULQWRWKHFKLPQH\
but ends 5 mm before the chimney inner wall. Possibly install a smoke
suction device*.
Soot hatch in the basement or attic that is open and thus
creating a false draught. Soot hatches must always be closed. Hatches that are not tight or are
defected must be changed.
'DPSHUWRSGUDXJKWYHQWVRUGRRUVRQ¿UHSODFHVWKDWDUH
not in use are open and create a false draught.
&ORVHGDPSHUGRRUVDQGWRSGUDXJKWYHQWVRQ¿UHSODFHVWKDWDUHQRWLQ
use.
$QRSHQKROHLQWKHFKLPQH\DIWHUWKDWD¿UHSODFHKDV
been removed, thus creating a false draught.
+ROHVPXVWEHFRPSOHWHO\VHDOHGRႇZLWKPDVRQU\
Defect masonry in the chimney, e.g. it is not airtight
DURXQGWKHÀXHSLSHHQWU\DQGRUEURNHQSDUWLWLRQLQVLGH
the chimney creating a false draught.
Seal and plaster all cracks and sites that are not tight.
The cross-section in the chimney is too large which
results in no or very low draught.
7KHFKLPQH\PXVWEHUH¿WWHGSRVVLEO\LQVWDOODVPRNHVXFWLRQGHYLFH
The cross-section in the chimney is too small and the
chimney cannot carry out all the smoke. &KDQJHWRDVPDOOHU¿UHSODFHRUEXLOGQHZFKLPQH\ZLWKDODUJHUFURVV
section. Possibly install a smoke suction device*.
The chimney is too low and hence a poor draught.
Increase the height of the chimney and/or install a chimney cap/smoke
suction device*.
7KH¿UHSODFH
releases smoke
inside when
LWLVZLQG\
outside.
The chimney is too low in relationship to the surrounding
terrain, buildings, trees etc. Increase the height of the chimney and/or install a chimney cap/smoke
suction device*.
Turbulence around the chimney due to the roof being
WRRÀDW
Increase the height of the chimney and/or install a chimney cap/smoke
suction device*.
7KH¿UHSODFH
does not heat
VXႈFLHQWO\
7KH¿UHSODFHFRPEXVWLRQUHFHLYHVWRRPXFKR[\JHQGXH
to a leakage under the lower border of the insert or too
VWURQJFKLPQH\GUDXJKW'LႈFXOWWRUHJXODWHWKHFRPEXV -
tion and the wood burn up too quickly.
$Q\SRVVLEOHOHDNDJHPXVWEHVHDOHGRႇ$GUDXJKWUHJXODWRURUSRVVLEO\
a damper can reduce the chimney draught. NB! A leakage of only 5 cm2
is enough for 30% of the heated air to disappear.
Too much
GUDXJKW
7KHVPRNHEXႇHULVZURQJO\SRVLWLRQHG 9HULI\WKHSRVLWLRQLQJRIWKHVPRNHEXႇHU±VHHDVVHPEO\LQVWUXFWLRQV
In case of using oven-dried wood, this requires less air
supply than when using normal wood.
Turn down the air supply.
7KHJDVNHWVDURXQGWKHGRRUDUHZRUQDQGWRWDOO\ÀDW Replace the gaskets, contact your dealer.
The chimney is too large. Contact chimneysweeper or other professional for more details.
7KHJODVVLV
VRRW\
The wood is too wet. Only use dry wood with a humidity of maximum 20%.
The air vent control is closed too tightly.
Open the air vent control to add air to the combustion. When new
wood logs are inserted all vent controls should be completely opened
RUWKHGRRUVOLJKWO\RSHQHGXQWLOWKHÀDPHVKDYHDJRRGWDNHRQWKH
wood.
:KLWHJODVV
Bad combustion (the temperature is too low). Follow the guidelines in this user guide for correct combustion.
Using wrong material for combustion (such as: painted
or impregnated wood, plastic laminate, plywood etc).
Ensure to use only dry and clean wood.
Smoke is
released when
the door is
opened
A levelling out of pressure occurs in the burn chamber.
Open the air vent control for about 1 min before opening the door –
avoid opening the door too quickly.
7KHGRRULVRSHQHGZKHQWKHUHLVD¿UHLQWKHEXUQ
chamber.
Open the door carefully and/or only when there is hot ember.
:KLWHVPRNH
The combustion temperature is too low. Increase the air supply.
The wood is humid and contains water damp. Ensure to use only dry and clean wood.
%ODFNRUJUH\
black smoke
,QVXႈFLHQWFRPEXVWLRQ Increase the air supply.