background image

 

 

Page  3 

YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE SHELTER

Thank you for purchasing our shelter. When properly assembled and maintained, this product will 

provide years of reliable service. These instructions include helpful hints and important information 

needed to safely assemble and properly maintain the shelter. Please read these instructions

 before

 you 

begin. 

If you have any questions during the assembly, please contact local dealer for assistance. 

 

SAFETY PRECAUTIONS 

. Wear eye protection. 

. Wear head protection

 

. Wear gloves when handling metal tubes 

. Use a portable GFCI (Ground Fault Circuit Interrupter) when working with power tools and cords. 

. Do not climb on the shelter or framing during or after construction. 

. Do not occupy the shelter during high winds, tornadoes, or hurricanes. 

. Provide adequate ventilation if the structure is enclosed. 

. Do not store hazardous materials in the shelter. 

. Provide proper ingress and egress to prevent entrapment. 
 

ANCHORING INSTRUCTIONS 

Prior to assembling this shelter, please read the

 MUST READ 

document included with the shipment. 

      WARNING:

 The anchor assembly is an integral part of the shelter construction. Improper anchoring 

may cause shelter instability and failure of the structure. Failing to anchor the shelter properly 

will void 

the manufacturer’s warranty

 and may cause serious injury and damage. 

 

LOCATION 

Choosing the proper location is an important step before you begin to assemble the structure. 

The following suggestions and precautions will help you determine whether your selected location is the 

best location. 

. Never erect the structure under power lines.   

. Identify whether underground cables and pipes are present

 before

 preparing the site or anchoring    the 

structure. 

. Location should be away from structures that could cause snow to drift on or around the building 

. Do not position the shelter where large loads such as snow and ice, large tree branches, or other 

overhead obstacles could fall. 

 

SITE 

After choosing a location, proper preparation of the site is essential. The following site characteristics will 

help ensure the integrity of the structure. 

. The support structure must be level to properly and safely erect and anchor the frame. 

. Drainage: Water draining off the structure and from areas surrounding the site should drain away from 

the site to prevent damage to the site, the structure, and contents of the structure. 

     

WARNING:

 The individuals assembling this structure are responsible for designing and furnishing all 

temporary bracing, shoring and support needed during the assembly process. For safety reasons, those 

who  are  not  familiar  with  recognized  construction  methods  and  techniques

  must  seek  the  help  of  a 

qualified contractor.         

 
 

Содержание SST304716




















Отзывы: