background image

4

19. Always stand on the foot rails when starting 

or stopping the walking belt. Always hold the 
handrails while using the treadmill.

20. When a person is walking on the treadmill, 

the noise level of the treadmill will increase.

21. Keep fingers, hair, and clothing away from 

the moving walking belt.

22. The treadmill is capable of high speeds. 

Adjust the speed in small increments to 
avoid sudden jumps in speed.

23. Never leave the treadmill unattended while it 

is running. Always remove the key, press the 
power switch into the off position (see the 
drawing on page 6 for the location of the 
power switch), and unplug the power cord 
when the treadmill is not in use.

24. Do not attempt to move the treadmill until it 

is properly assembled. (See ASSEMBLY on 
page 8 and HOW TO FOLD AND MOVE 
THE TREADMILL on page 29.) You must be 
able to safely lift 45 lbs. (20 kg) to move the 
treadmill.

25. When folding or moving the treadmill, make 

sure that the storage latch is holding the 

frame securely in the storage position. Do 
not operate the treadmill while it is folded.

26. Do not change the incline of the treadmill by 

placing objects under the treadmill.

27. Never insert any object into any opening on 

the treadmill.

28. Inspect and properly tighten all parts each 

time the treadmill is used.

29. 

DANGER:

 Always unplug the power 

cord immediately after use, before clean-
ing the treadmill, and before performing the 
maintenance and adjustment procedures 
described in this manual. Never remove the 
motor hood unless instructed to do so by an 
authorized service representative. Servicing 
other than the procedures in this manual 
should be performed by an authorized ser-
vice representative only.

30. Over exercising may result in serious injury 

or death. If you feel faint, if you become short 
of breath, or if you experience pain while 
exercising, stop immediately and cool down.

SAVE THESE INSTRUCTIONS

Содержание NTL99520.0









































Отзывы: