11
NORDIC
9.
Clean the tank, nozzle guard, nut, nozzle, air flow regulator, gun assembly, etc with
a brush and cleaning solution.
Note: Never use sharp metal needle or similar to clean the nozzles! Never
use silicone-containing solvent or lubricant to clean the nozzles! Do not
miss the nozzle seal.
10.
Install the removed parts.
11.
When battery pack is not in use for long time, it should be stored it separately.
MAINTENANCE
After using for a period of time, you should check if the filter is dirty or not. If it is too dirty, you need to
replace the filter with the following steps.
1.
Remove the battery pack, and the filter guard by screwdriver.
2.
Remove the dirty filter and replace it with a new one.
3.
Reinstall the filter guard.
Never operate the spray gun without a filter! The dirt will be sucked into the appliance and cause a damage.
STORING
Store the machine, operating instructions and where necessary the accessories in the original packaging in
a dry place. In this way you will always have all the information and parts ready to hand.
C
Cl
le
ea
an
ni
in
ng
g
Cleaning the spray gun
Note: Do not immerse the gun in the detergent!
1.
Unlock the fan assembly and remove it from the gun assembly.
Align the release latch and pull out the gun. Press the trigger so
that the spray material remaining in the gun flows into the
container.
2.
unlock and remove the tank, empty the residual spraying material
in the tank.
3.
For cleaning, pour a little cleaning
solution into the tank.
After washing, the residual liquid
should be properly disposed to
avoid environmental pollution.
4. refill new cleaning solution.
5. Screw back the tank with the
Cleaning solution onto the
spray gun.
6
. Spray cleaning solution for a few seconds
（
2-5s
）
in safety area, spray for a
few few seconds again. Then remove the
tank and press the trigger.
7. Wipe and clean the outside of the tank.
8. remove the adjusting knob, nut, Nozzle guard, nozzle, etc.
9. Clean the tank, nozzle guard, nut, nozzle, air flow regulator, gun
assembly, etc. with a brush and cleaning solution.
Note: Never use sharp metal needle or similar to clean the nozzles!
Never use silicone-containing solvent or lubricant to clean the nozzles!
Do not miss the nozzle seal.
10. Install the removed parts.
11.
When battery pack is not in use for long time, it should be stored
it separately.
7
Check
valve
M
Ma
ai
in
nt
te
en
na
an
nc
ce
e
After using for a period of time, you should check if the filter is
dirty or not. If it is too dirty, you need to replace the filter with the
following steps.
1. Remove the battery pack, and the filter guard by screwdriver.
2.
Remove the dirty filter and replace it with a new one.
3. reinstall the filter guard.
Never operate the spray gun without a filter! The dirt will be
sucked into the appliance and cause a damage.
T
Tr
ro
ou
ub
bl
le
es
sh
ho
oo
ot
ti
in
ng
g
PPrroobblleemm ddeessccrriippttiioonn
A.
spray with low flow rate or no spray
B. Spraying material drips
C.
Bad atomization
D.
Spraying fluctuation
E.
Hanging phenomenon of spray material
F.
Over spraying
G.
Spray pattern too thin
RReeaassoon
nss
1. Nozzle clogged
2. Suction tube clogged
3. Flow regulator set in low position
4. Suction tube loose
5. tank loose
6. Filter clogged
1. Nozzle loose
2. Nozzle damaged
3. Nozzle seal damaged
4. Spraying material accumulated in nozzle
1. High viscosity of spray material
2. High flow rate of spray material
3. Flow regulator set high position
4. Nozzle clogged
5. Filter clogged
6. low pressure build-up in the tank
1. Spray material is not enough in tank
2. Filter clogged
1. spray too much material
1. long distance between spray gun and surface
2. high flow rate of spray material
1. move the spray gun too fast
SSoolluuttiioonnss
1. Clean the nozzle
2. Clean the suction tube
3. adjust the flow regulator
4. tighten the suction tube
5. tighten the tank
6. replace the filter
1. tighten the nozzle
2. replace the nozzle
3. replace the nozzle
4. Clean the nozzle
1. Dilute the spray material
2. Reduce the flow rate
3. adjust the flow regulator
4. Clean the nozzle
5. Replace the filter
6. Tighten the tank
1. Refill the spray material
2. Replace the filter
1. reduce the flow rate or move the spray gun faster
1. reduce the distance
2. reduce the flow rate
1. increase the flow rate or move the spray gun
slower
9
filters
MMaaiinntteennaan
nc
cee
After using for a period of time, you should check if the filter is
dirty or not. If it is too dirty, you need to replace the filter with the
following steps.
1. Remove the battery pack, and the filter guard by screwdriver.
2.
Remove the dirty filter and replace it with a new one.
3. reinstall the filter guard.
Never operate the spray gun without a filter! The dirt will be
sucked into the appliance and cause a damage.
T
Tr
ro
ou
ub
bl
le
es
sh
ho
oo
ot
ti
in
ng
g
P
Pr
ro
ob
bl
le
em
m
d
dees
sccr
riippt
ti
io
onn
A.
spray with low flow rate or no spray
B. Spraying material drips
C.
Bad atomization
D.
Spraying fluctuation
E.
Hanging phenomenon of spray material
F.
Over spraying
G.
Spray pattern too thin
RReeaasso
onnss
1. Nozzle clogged
2. Suction tube clogged
3. Flow regulator set in low position
4. Suction tube loose
5. tank loose
6. Filter clogged
1. Nozzle loose
2. Nozzle damaged
3. Nozzle seal damaged
4. Spraying material accumulated in nozzle
1. High viscosity of spray material
2. High flow rate of spray material
3. Flow regulator set high position
4. Nozzle clogged
5. Filter clogged
6. low pressure build-up in the tank
1. Spray material is not enough in tank
2. Filter clogged
1. spray too much material
1. long distance between spray gun and surface
2. high flow rate of spray material
1. move the spray gun too fast
S
So
ol
luut
tiio
on
nss
1. Clean the nozzle
2. Clean the suction tube
3. adjust the flow regulator
4. tighten the suction tube
5. tighten the tank
6. replace the filter
1. tighten the nozzle
2. replace the nozzle
3. replace the nozzle
4. Clean the nozzle
1. Dilute the spray material
2. Reduce the flow rate
3. adjust the flow regulator
4. Clean the nozzle
5. Replace the filter
6. Tighten the tank
1. Refill the spray material
2. Replace the filter
1. reduce the flow rate or move the spray gun faster
1. reduce the distance
2. reduce the flow rate
1. increase the flow rate or move the spray gun
slower
9
filters
