background image

8

NORDIC

The fastening torque is affected by a wide variety of factors including the following. After fastening, always 
check the torque with a torque wrench.
1.  When the battery cartridge is discharged almost completely, voltage will drop and the fastening 

torque will be reduced.

2.  Driver bit or socket bit 

 

Failure to use the correct size driver bit or socket bit will cause a reduction in the fastening torque.

3.  Bolt

•  Even though the torque coefficient and the class of bolt are the same, the proper fastening torque will differ 

according to the diameter of bolt. 

•  Even though the diameters of bolts are the same, the proper fastening torque will differ according to the torque 

coefficient, the class of bolt and the bolt length.

4.  The manner of holding the tool or the material of driving position to be fastened will affect the 

torque.

5.  Operating the tool at low speed will cause a reduction in the fastening torque

8. CLEANING AND MAINTENANCE

8.1 CLEANING

•  Keep the ventilation slots of the machine clean to prevent overheating of the engine.

•  Regularly clean the machine housing with a soft cloth, preferably after each use.

•  Keep the ventilation slots free from dust and dirt.

• 

⦁If the dirt does not come off use a soft cloth moistened with soapy water.

• 

⦁Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.

8.2 MAINTENANCE

Our machines have been designed to operate over a long period of time with a minimum of maintenance. 
Continuous satisfactory operation depends upon proper machine care and regular cleaning.

9. REPAIR

This product does not contain any parts that can be repaired by the consumer. Contact a qualified specialist 
to have it checked and repaired.

10. ENVIRONMENT

Should your appliance need replacement after extended use, do not dispose of it with the household 
refuse, but in an environmentally safe way.
Waste produced by electrical machine items should not be handled like normal household rubbish. Please 
recycle where recycle facilities exist. Check you’re your Local Authority or retailer for recycling advice.

Содержание POBA2100









Отзывы: