background image

 

____________________________________________________________________________________ 
 

____________________________________________________________________________________ 
Speeder X1 and X2 Configuration and API Guide  

Page 31/36

 

12,13 

Trigger Distance Beam A 
 
Mode 7&5 (Chapter 4.1&5.1): Minimum 
distance value for Beam A trigger window 
Mode 12 (Chapter 0): Minimum detection 
distance for speed measurement 

cm 

0 - 38000 

 

14 

Trigger Window Width 
 
Window size of triggering, starting from the 
value in P12,13 

dm 

1 - 255 

 

15 

Hits For Trig 
 
Number of accepted measurement values 
before activating trigger pulse 

smpls 

0 - 255 

>= 5 

17 

Trigger Length 
 
Note: In the case of speed measurement, the 
minimum length of the trigger is defined by the 
time of speed calculation. 
In the same mode setting Trigger Length = 255 
keeps the trigger active until vehicle has 
passed the measurement point. 

ms 

0 - 255 

255 

18 

Clear Check Time 
 
Time from the last measurement in the trigger 
window required to re-activate Triggering 
mode. 

10 ms 

0 - 255 

30 

26 

Control Byte 3 (See Chapter 6.6) 

 

 

 

29,30 

Speed Pulse Rate 
 
Speed pulse rate is in use after detection of a 
vehicle in speed measurement application (or 
mode). Speeder X1 is class 1 laser product. 
Eye-safety standard limits the pulse rate of 
Speeder X1 to 2000 Hz for pulse trains in short 
range (Condition 2, target distance less than 2 
meters). Laser pulsing exceeding 2000 Hz is 
allowed only while measured distance is more 
than 2 meters. Pulse train limitations are 
controlled programmatically to fulfil the 
Standard EN 60825-1:2007 (IEC 60825-
1:2007) Condition 2.  

Hz 

2000 

– 

8000 

4000 

31 

Speed Calculation Start 
 
The starting point of speed calculation: This 
parameter defines how long a distance from 
the triggering point is rejected in speed 
calculation. 

dm 

2 - 10 

 

32 

Speed Geometry 
 
Dimensional offset of the sensor from the line 
of movement of the measured object  
E.g. height of the Sensor  above the road 
surface, 55 dm 

dm 

0 - 255 

 

36 

Speed Limit Large 
 
A speed limit for vehicles higher than defined 
by parameter 39.  
Notice that it can only be used with top of the 
road installations and mode 7 (Speed mode 
For Vertical Installation) 
 

km/h 

0 - 255 

 

Содержание speeder x1





































Отзывы: