NookBox E6309744 Скачать руководство пользователя страница 6

6

NookBox

Installation Guide

Keypad 

Installation Procedures

Step 1. 

Put the Control panel into learning mode.

Step 2. 

Adding remote keypad into the Control Panel:

   

Test Mode Learning:

 

 

1. 

Put remote keypad in Test mode by entering KP PIN code (default: 

0000

), then press 

*

 key. The Active Amber LED will    

 

 

 

turn on along with a long beep sound.

  

2. Press 

*

 key then 

7

 key. Remote keypad will sound a long beep.

  

<NOTE>

  

•  If the remote keypad did not sound a long beep, it means the remote keypad did not send the learning code to the Control Panel, please    

  

  press 

*

 key then 

7

 key again to send the learning code.

 

 

3. 

If the Control Panel receives the learning code, it will display the info accordingly. Refer to the operation manual of your   

 

 

 

Control Panel to complete the learn-in process.

 

 

4. 

After Control Panel receives the signal from remote keypad, it will send an acknowledgement back to remote keypad. The  

 

 

 

remote keypad will then beep 3 times to confirm the acknowledgement has been received.

   

Dual-Key Learning:

 

 

1. 

Press and both 

#

 and 

*

 keys together under Normal Operation Mode. Remote Keypad will sound a long beep.

  

<NOTE>

  

• 

If the remote keypad did not sound a long beep, it means the remote keypad did not send the learning code to the Control Panel, please    

 

 

 

press both # and 

*

 keys together again to send the learning code.

 

 

2. 

If the Control Panel receives the learning code, it will display the info accordingly. Refer to the operation manual of your   

 

 

 

Control Panel to complete the learn-in process.

 

 

3. 

After Control Panel receives the signal from remote keypad, it will send an acknowledgement back to remote keypad. The  

 

 

 

remote keypad will then beep 3 times to confirm the acknowledgement has been received.

 

 

<IMPORTANT NOTE>

  

• 

If remote keypad does not perform 3 beeps, please restart the learning procdeure.

Step 3.

  After the Remote keypad is learnt-in, put the Control Panel into 

Walk Test

 mode, hold the Remote keypad in the desired  

 

 

 

location, and send the learning code to the Control Panel to confirm this location is within the signal range of the Control Panel. 

 

 

To send the learning code, either press the 

*

 key then 

7

 key under Test Mode or press both 

#

 and 

*

 keys together under 

 

 

Normal Operation Mode.

Step 4.

  When you are satisfied that the Remote keypad works in the chosen location, you can proceed with mounting the Remote 

 

 

keypad following the steps described below (see 

Mounting Remote keypad

).

Step 5.

  Set your own the KP Pin Code:

 
 

 

1. 

When the keypad is under Test mode, press 

*

 key then 

6

 key, a long beep will be sound.

  

2. Enter 

0000

 (default PIN code)

  

3. Press   key, remote keypad sounds a long beep.

 

 

4. 

Enter your new 4-digit code.

  

5. Press 

#

 key, remote keypad sounds a long beep. The new PIN code is enabled.

Step 6.

 Press   key 

twice

 to leave Test mode and the installation is completed.

Содержание E6309744











Отзывы: