NOMACORC NomaSense CO2 P2000 Скачать руководство пользователя страница 5

Страница: 5 / 12

TEMP./MEMORY key

Activates the temperature

selection function. Key is also

used to scroll through the saved

measurements.

(1) Needle holder

Place the needle (5) in the holder when

not in use.

(2) Main display

Shows the measurement result and the

temperature setting.

(3) Connector for external power supply/

battery charger

See “External power supply/battery

charger” for details.

(4) Collected measurements display

Shows the number of a stored

measurement. The corresponding

measurement result

and temperature is displayed in the main

display (2). See “Memory function” for

details.

(5) Needle
(6) Filter/Water trap

Protects the device from particles and

liquids.

(7) Pressure relief valve

Use to perform a pressure relief of the test

bottle before measuring.

Содержание NomaSense CO2 P2000













Результаты поиска

Содержание NomaSense CO2 P2000

Отзывы:

Похожие инструкции для NomaSense CO2 P2000

Бренды по названию

Популярные бренды

NOMACORC NomaSense CO2 P2000, Руководство пользователя

Результаты поиска

Содержание NomaSense CO2 P2000

Отзывы:

Похожие инструкции для NomaSense CO2 P2000

Бренды по названию

Популярные бренды