When you get near the remote control like in the shown position
of the picture (the oscillator should be already plugged in) press
the button with a pencil and turn slowly the potentiometer with a
ceramic screw-driver.
The
COPY-CONTROL
show a first adjustment level and the better
one is 1023.
We suggest you to put the remote control as near as you can in
the
COPY-CONTROL
and then remove it 3-5 cm to reach the
value 1024. We recommend not turn strong the potentiometer but
do it slowly.
To go out press the button esc
P2.
FUNCTION 2
Put the antenna on the remote X to check like in the photo. Then press the button of the copy remote control to check if it has
well copied the code. When the
COPY-CONTROL
take the radio signal, the two
RED LIGHTS flash faster
. The right learning
of the remote control will be confirmed from the turning on of the
YELLOW LIGHTS
and the simultaneously showing on in the
display of the 100%. (The
YELLOW L.E.D.
will turn on only when the code is
100%
copied)
Release the button
P2
.
FUNCTION 3
Pay attention that this function reachable only if you are already in the FUNCTION no.3 and after learning a code in the
memory of the
COPY-CONTROL
. In this situation if you press the button
P2
, keep it pressed, confirm it pressing and re
leasing the
P1
, (
P2
+
P1
and then release). After this operation you have a constantly transmission of the memory code,
this is confirmed when a flashing
“ t “
will be displayed as shown in the picture.
Now, putting a remote control as shown in the picture, we can clone that code directly from the
COPY-CONTROL
, to make
easy the copy of the remote control which have the same code and besides this is useful in case of difficult copy because
you can hang on the better sensitivity of the
COPY-CONTROL
.
FUNCTION 3/Bis
Nologo srl declares that COPY-CONTROL is conformed to the essential requirements of the following norms:
ETSI EN 301 489-3
EN 300 220-1 EN 300 220-3
EN 60950: 1997
Me Ernestino Bandera the administrator, declares that the remote control has been tested in a typical installation and satisfies all
essential requirements of the directives: 99/5/CE
Ernestino Bandera
Busto Arsizio, 01.10.2008
Conformity Declaration
2002/95/EC
RoHS
C O M P L I A N T
To select the function 2 with the button
P1
, keep it pressed until you’ll see in the display the code in the picture.
Press the button
P2
to enter in the program.
Now the
COPY-CONTROL
is ready to receive a signal of a remote control (low frequencies) to display the adjustment level.
Choose the function no.3 with the button
P1
and keep it pressed till in the display you see the same number as in the picture.
Press and keep pressed the button
P2
to memorize in the
COPY-CONTROL
the original code X.
Now the
COPY-CONTROL
that has already memorize the remote
control , now it can compare the code with the next one Y.
Put the remote control Y and press the button and check it.
If the transmitted code is the same of the previous learned remote
control, the
YELLOW L.E.D.
and the percentage of the right
memorization the l.e.d. will turn on in the same time..
If the copy of the remote control hasn’t copied
100%
well the code
the blue lights will turn on and a low percentage (less then 100%) the
code is different of the previously memorized.
If we test with a rolling code remote control we can check that the learning and the comparison with the same button will give a
negative result (
BLUE L.E.D.
and low percentage) to confirm that it is a rolling code and it cannot be copied.
This is not valid for the fixed part of the code which can be indicated in the percentage of the code (rolling code)
