Nokia NSB-1 Series Скачать руководство пользователя | Manualshive

Страница: 19 / 24

background image

PAMS

Technical Documentation

NSB–1/3

Troubleshooting Instructions

Page 19

Original 06/98

SIM card is out of order

The hardware of the SIM interface from MAD2 (D200) to the SIM connec-
tor (X302) can be tested without SIM card.
When the power is switched on and if the BSI line (X101;1) is grounded
by resistor, all the used lines (VSIM, RST, CLK, DATA) rise up four times.
Thus ”Insert SIM card” faults can be found without SIM card.
The fault information ”Card rejected” means that ATR message (the first
message is always sent from card to phone) is sent from card to phone
but the message is somehow corrupted, data signal levels are wrong etc.
or factory set values (stored to the EEPROM) are not correct.

«
...
17
18
19
20
21
...
»

Содержание NSB-1 Series

























Отзывы:

Нет отзывов

Похожие инструкции для NSB-1 Series

Бренд: Parallel Audio Страницы: 8

Бренд: XIEGU Страницы: 20

Бренд: XIEGU Страницы: 17

Бренд: Yaesu Страницы: 96

Бренд: Yaesu Страницы: 195

Бренд: Yaesu Страницы: 39

Бренд: dikom Страницы: 21

Бренд: FUTABA Страницы: 22

Бренд: Rough and Ready Страницы: 14

Бренд: Samson Страницы: 24

Бренд: Steren Страницы: 3

Бренд: Omega Страницы: 24

Бренд: Kantronics Страницы: 10

Бренд: nologo Страницы: 10

Бренд: SILENTSYSTEM Страницы: 9

Бренд: Allstar Products Group Страницы: 2

Бренд: X-Digital System Страницы: 11

Бренд: REFI Multimedia Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды