manualshive.com logo in svg

Nokia NPM-2NX, Руководство по устранению неисправностей

Поделиться
Скачать
Nokia NPM-2NX Скачать руководство пользователя страница 44

NPM-2NX

Troubleshooting

CCS Technical Documentation

Page 44

 

ã

Nokia Corporation

Issue 1 07/02

Transmitter

General instructions for TX troubleshooting

Always use an RF-cable connected from an external RF-connector to analyzer via (rf-
power) attenuator. This is important to protect analyzer against excessive RF-power and 
not allow leakage of undesired RF-power into RF-power into cellular frequencies.

AMPS/TDMA

Start Phoenix-software and select TX mode under testing (AMPS, DAMPS or TDMA1900). 
It is useful to select mid channel (383 for AMPS/DAMPS or 1000 for TDMA1900) and 
power level 2. Select random data for digital mode of operation.

After any component change tune the phone with Phoenix auto tune SW.

GSM1900

Start Phoenix-software and select GSM RF Control, PL0, Ch661 and TX data type random.

Path of the transmitted signal

AMPS/DAMPS

UEM TX I/Q DA-converters -> I/Q modulator and Digital gain step amplifier (SAFARI) -> 
Dual TX IF-BPF -> Up converter (mixer -> C904 -> driver) -> BPF -> PA -> Power detec-
tor -> Duplex-filter -> Diplexer -> EXT RF-connector -> Antenna

TDMA1900, GSM1900

UEM TX I/Q DA-converters -> I/Q modulator and Digital gain step amplifier (SAFARI) -> 
Dual TX IF-BPF -> Up converter (Mixer -> BPF -> Driver) -> BPF -> PA -> Power detector 
-> Duplex-filter -> Diplexer -> EXT RF-connector -> Antenna

The power detection and power control circuit belongs under power control part of this 

Содержание NPM-2NX



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды