manualshive.com logo in svg

Nokia NPM-2NX, Руководство по устранению неисправностей

Поделиться
Скачать
Nokia NPM-2NX Скачать руководство пользователя страница 24

NPM-2NX

Troubleshooting

CCS Technical Documentation

Page 24

 

ã

Nokia Corporation

Issue 1 07/02

No sound: Try using known good buzzer instead. If still no sound ->change UEM(D200)

Weak sound: Use Audio test in Phoenix to set buzzer parameters(frequency, strength). If 
it doesn't effect to the sound level ->change buzzer.

Vibra does not work

Check spring connectors and C307.

No vibration: Try using known good vibra instead. If still no vibration -> change 
UEM(D200)

Weak vibration: Use Vibra test in Phoenix to set vibra parameters(frequency, duty cycle). 
If it doesn't effect to the magnitude of vibration ->change vibra.

Keyboard does not work

Check that there is no dirt between the dome sheet and the PWB and also check that 
Z300 is properly soldered and the cornner mark is located in the right place. If the key-
board still doesn't operate normally -> try to use Keyboard test in Phoenix to see if the 
pressed key is identified. If not ->change UPP(D400), then if this does not help, also 
change the Z300.

SIM does not work

Check SIM reader's spring connectors, C390 (VSIM 3.0V) and R388. If SIM still does not 
work then probably the UEM or the UPP is broken -> change first one component and 
check the phone.

Содержание NPM-2NX



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды