Nokia NPM-10 Series Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 48

Nokia NPM-10 Series Скачать руководство пользователя страница 48

NPM-10

Troubleshooting Instructions RF

CCS Technical Documentation

Page 48



Nokia Corporation Confidential

Issue 1 03/2003

RF Control

Phoenix menu: Select Maintenance, Testing, RF Controls

It is meant to check the receiver or transmitter without going in a call. It works very
much like a call, but you have control via the PC, and not via the tester. The GSM850 TX
PA mode should be set to High.

If you want to tune at other channels than the default, then you must select it first in RF
control and then start the tuning.

Call Testing

If all tunings are done, and the phone TX and RX is working, a call is the ultimate test of
the phone.

Set the communications tester to manual test. Switch the phone to normal if it was in
local mode. Remember to have a test simcard in the phone.

After the phone has registered to the communications tester, a call can be made. It is
possible to let the phone answer via Phoenix. In the Autocaller (Maintenance Testing)
you can answer by ticking Answer when button pushed and then push the button.

«
...
46
47
48

Содержание NPM-10 Series

















































Отзывы:

Нет отзывов