manualshive.com logo in svg

Nokia NPM-10 Series, Инструкции по устранению неисправностей, Страница: 3 / 48

Поделиться
Скачать
Nokia NPM-10 Series Скачать руководство пользователя страница 3

CCS Technical Documentation

Troubleshooting Instructions RF

NPM-10

Issue 1 03/2003

Nokia Corporation          Confidential

Page 3

Contents

Page No

Abbreviations in Troubleshooting Charts ....................................................................5
Introduction ..................................................................................................................5
General Description of the RF Circuits  .......................................................................6

Receiver Signal Path ................................................................................................. 6
Transmitter Signal Path ............................................................................................. 7
PLL............................................................................................................................ 8
Key RF Component Placement ............................................................................... 10
Power Supply Configuration ................................................................................... 11

Receiver .....................................................................................................................13

General Instructions for GSM850 RX Troubleshooting ......................................... 13
Troubleshooting Chart for GSM850 Receiver ........................................................ 15
General Instructions for GSM1900 RX Troubleshooting ....................................... 16
Troubleshooting Chart for PCS Receiver................................................................ 18
Measurement Points in the Receiver....................................................................... 20

Transmitter .................................................................................................................22

Measurement Points for the Transmitter ................................................................. 22
General Instructions for GSM TX Troubleshooting ............................................... 23
Troubleshooting Chart for GSM850 Transmitter.................................................... 24
General instructions for PCS TX troubleshooting .................................................. 26

Synthesizer .................................................................................................................29

General Instructions for Synthesizer Troubleshooting............................................ 29
26 MHz Reference Oscillator ( VCXO )................................................................. 30
VCO ........................................................................................................................ 30
 Troubleshooting Chart for PLL Synthesizer .......................................................... 31
Measurement Points for the PLL ............................................................................ 32
Frequency Lists ....................................................................................................... 34

Alignment ..................................................................................................................36

3595 Manual Align with Phoenix ........................................................................... 36
RX Calibration ........................................................................................................ 37
RX Channel Select Filter......................................................................................... 39
RX Band Filter Response ........................................................................................ 40

Tx Tuning  ..................................................................................................................41

TX Power Tuning GSM850 .................................................................................... 43
TX Power Tuning PCS1900.................................................................................... 44

TX I/Q Tuning  ...........................................................................................................44
RF Control  .................................................................................................................48
Call Testing ................................................................................................................48

Содержание NPM-10 Series

















































Отзывы:

Нет отзывов