manualshive.com logo in svg

Nokia 7360 Intelligent Services Access Manager FX Series, Руководство пользователя, Страница: 579 / 626

Поделиться
Скачать
Nokia 7360 Intelligent Services Access Manager FX Series Скачать руководство пользователя страница 579

FD 100/320Gbps NT and FX NT IHub Services Guide

Virtual Private Routed Network Service

Issue: 13

3HH-11985-AAAA-TQZZA

579

 

Table 

634

 describes the command output fields for a BGP neighbor.

Table 634

Show BPG Neighbor Output

Description

This command displays BGP neighbor information. This command can be entered with or 
without any parameters. 
When this command is issued without any parameters, information about all BGP peers 
displays.
When the command is issued with a specific IP address or ASN, information regarding only 
that specific peer or peers with the same AS display.
When either received-routes or advertised-routes is specified, then the routes received from or 
sent to the specified peer is listed (see second output example). 

Note

: This information is not available by SNMP.

When either history or suppressed is specified, then the routes learned from those peers that 
either have a history or are suppressed (respectively) are listed.
The ‘State’ field displays the BGP peer’s protocol state. In additional to the standard protocol 
states, this field can also display the ‘Disabled’ operational state which indicates the peer is 
operationally disabled and must be restarted by the operator.

Parameters

ip-address

— Displays the BGP neighbor with the specified IP address.

family

 

family

— Selects the address family to be shown

Values: 

ipv4

 — Displays only those BGP peers that have the IPv4 family enable and not those 

capable of exchanging IP-VPN routes.

ipv6

 — Displays the BGP peers that are IPv6 capable.

filter1

— Specifies route criteria.

Values: received-routes, advertised-routes, history, suppressed, detail

filter2

— Specifies route criteria.

Values: history, suppressed, detail

Label

Description

Peer

The IP address of the configured BGP peer.

Group

The BGP peer group to which this peer is assigned.

Peer AS

The configured or inherited peer AS for the peer group.

Peer Address

The configured address for the BGP peer.

Peer Port

The TCP port number used on the far-end system.

Local AS

The configured or inherited local AS for the peer group.

Local Address

The configured or inherited local address for originating peering for the peer group.

Local Port

The TCP port number used on the local system.

Peer Type

External — Peer type configured as external BGP peers.
Internal — Peer type configured as internal BGP peers.

(1 of 4)

Item

Description

(2 of 2)

Содержание 7360 Intelligent Services Access Manager FX Series



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов