Nokia 7360 Intelligent Services Access Manager FX Series Скачать руководство пользователя страница 49

Страница: 49 / 626

FD 100/320Gbps NT and FX NT IHub Services Guide

Services Overview

Issue: 13

3HH-11985-AAAA-TQZZA

Figure 2

Service Access Point (SAP)

3.4.2.1

SAP Configuration Considerations

When configuring a SAP, consider the following:

•

An SAP is a local entity and only locally unique to a given device. The same SAP

ID value can be used on another ISAM/service router.

•

There are no default SAPs. All SAPs in subscriber services must be created.

•

The default administrative state for a SAP at creation time is administratively

enabled.

•

When a SAP is deleted, all configuration parameters for the SAP will also be

deleted. For Internet Enhanced Service (IES), the IP interface must be shutdown

before the SAP on that interface may be removed.

•

A SAP is owned by and associated with the service in which it is created in each

ISAM.

•

If a port is administratively shutdown, all SAPs on that port will be operationally

out of service.

•

A SAP cannot be deleted until it has been administratively disabled (shutdown).

•

Each SAP can have one each of the following policies assigned:

•

Ingress filter policy

•

Egress filter policy

3.4.3

Service Distribution Points (SDPs)

A service distribution point (SDP) acts as a logical way to direct traffic from one ISAM

to another PE through a uni-directional (one-way) service tunnel. The SDP

terminates at the far-end ISAM/service router which directs packets to the correct

service egress SAPs on that device. A distributed service consists of a configuration

with at least one SAP on a local node, one SAP on a remote node, and an SDP

binding the service to the service tunnel.

Customer

IP Network

SAP

3/1/6

dot1q

SAP

2/2/3

dot1q

Service

Cust-27

SAP

ALA-A

Customer

Содержание 7360 Intelligent Services Access Manager FX Series


















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 7360 Intelligent Services Access Manager FX Series

Отзывы:

Nokia 7360 Intelligent Services Access Manager FX Series, Руководство пользователя, Страница: 49 / 626

Результаты поиска

Содержание 7360 Intelligent Services Access Manager FX Series

Отзывы: