Nixie Clock ITS1A Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 29

background image

12

ITS1A CLOCK

Display Header and Connector

This is a picture of the front of the display board. This is the side the tubes will be visible from.

Connectors

It connects at right-angles to the main board. A 1x20 socket is soldered to the main board, and a 20-pin
right-angled header is soldered to the display board. The two are held together using right-angled
brackets:

This is one way to make sure that everything lines up, when the socket and header are soldered in place:

1.

Install the brackets on the main board.

«
...
10
11
12
13
14
...
»

Содержание ITS1A






























Отзывы:

Нет отзывов

Похожие инструкции для ITS1A

Бренд: La Crosse Technology Страницы: 8

Бренд: Memorex Страницы: 11

Бренд: Manta Страницы: 16

Бренд: THOMSON Страницы: 49

Бренд: Lathem Страницы: 63

Бренд: Pike Страницы: 9

Бренд: Trevi Страницы: 8

Бренд: Somogyi Страницы: 12

Бренд: Somogyi Страницы: 11

Бренд: Somogyi Страницы: 11

Бренд: Somogyi Страницы: 11

Бренд: Sharper Image Страницы: 4

Бренд: Sharper Image Страницы: 6

Бренд: La Crosse Technology Страницы: 5

Бренд: AcuRite Страницы: 8

Бренд: Jazwares Страницы: 18

Бренд: DCS Страницы: 1

Бренд: PYE Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды