Niveo NGSM48T2 Скачать руководство пользователя страница 158

Страница: 158 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 158

Port Isolation Configuration

Overview

This page is used for enabling or disabling port isolation on ports in a Private VLAN..

A port member of a VLAN can be isolated to other isolated ports on the same VLAN

and Private VLAN.

The port settings relate to the currently selected stack unit, as reflected by the page

header.

This feature works across the stack.

Configuration

Port Members

A check box is provided for each port of a private VLAN. When checked, port

isolation is enabled on that port. When unchecked, port isolation is disabled on that

port.

By default, port isolation is disabled on all ports.

Buttons

Save:

Click to save changes.

Reset:

Click to undo any changes made locally and revert to previously saved

values.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды