niu N-GT Скачать руководство пользователя

Страница: 142 / 144

V1.0.0

142

Regular Maintenance Checklist

Inspection of Wheels and Tires

•

Support the scooter with the Central Stands.

•

Lift up the Front/Rear Wheel to check range of the free travel.

•

Hold the Front/Rear Wheel and try to move it leftward and rightward to check the front wheel
bearing for wearing.

•

Replace the Front/Rear Wheel bearing if it becomes loosened.

•

Turn the wheel to make sure that it can be rotated smoothly without an abnormal noise.

•

The Front/Rear Wheel bearing should be inspected as long as there are suspicious abnormal
conditions.

•

Check the tire pressure with the tire pressure gauge when the tire has been cooled down.

•

Recommended

tire

pressure:

•

Check the tire for cuts, embedded nails or other damages.

•

Check flatness of the front and rear wheels.

•

Check tread depth.

Wheel bearing

Rear wheel bearing

Steering
column
bearing

Front tire

20-25psi

Rear tire

26-32psi

Air pressure gauge

Содержание N-GT

















































































































































Результаты поиска

Содержание N-GT

Отзывы:

Похожие инструкции для N-GT

Бренды по названию

Популярные бренды

niu N-GT, Руководство по обслуживанию

Результаты поиска

Содержание N-GT

Отзывы:

Похожие инструкции для N-GT

Бренды по названию

Популярные бренды