background image

3

power source.  Do not leave the work area until the 

tool comes to a complete stop. 

MAINTENANCE/SERVICE

 Do not take apart or modify tool.

Disassembly or modification carried out without 

the supervision of a qualified or authorized service 

engineer could result in an accident or injury.

 Inspect cutting tool and accessories, etc. 

Always  check  to  see  that  cutting  tool  and 

accessories, etc. are in good operating condition 

without damage or deterioration before you mount 

them on the tool.  Should you find any damage to 

an accessory or part, please contact sales agent 

through which you have purchased your tool or an 

authorized dealer near you for repair.

 Check parts for damage. 

When you have found damage to accessory or other 

part, carefully check the damaged part to determine 

the extent of influence it has upon the functions 

of the tool – that is, determine whether it can still 

perform its normal functions. 

Check to see that the linkage of the moving parts 

is  OK,  that  all  parts  are  OK  without  damage, 

that they are properly mounted, and that the tool 

functions normally. Should you find any damage 

to an accessory or part that may hamper proper 

functioning of the tool, please contact sales agent 

through which you have purchased your tool or an 

authorized dealer near you for repair.

 Have your tool repaired at an authorized Nitto 

Service Center. 

For repair or parts replacement, please contact the 

sales agent through which you have purchased your 

tool or an authorized dealer near you.

 Use only Nitto genuine parts. 

Use of improper parts may result in serious accident.

To obtain a Nitto genuine part, consult this Manual 

or contact the sales agent from which you have 

purchased your tool directly. 

 Do not detach label or nameplate from tool. 

When a label/nameplate gets damaged, worn or 

becomes missing, contact the sales agent through 

which you have purchased your tool or Nitto Kohki 

Co. Ltd, directly for a replacement. 

DISPOSAL

When a tool is taken permanently out of service, it is 

advised that the tool is disassembled, degreased and 

parts separated by material and recycled locally in the 

appropriate manner.

GENERAL:  PNEUMATIC 

TOOLS

WARNING

 Use appropriate air pressure.

Excessively high air pressure will increase the tool 

number of revolutions or strokes causing not only 

potential premature failure/breakage but could also 

lead to an unexpected accident or injury.

 Connect tool to air supply line.

There are various types of pipes running in a factory 

in addition to the pneumatic line (such as oxygen, 

nitrogen, gas and water). For this reason, always 

ensure that you are connecting to the pneumatic 

line.

 Start tool properly.

Turn the start switch OFF before connecting to the 

air supply line.

 Always disconnect the tool from the air supply 

line before putting on/taking off any accessory 

and prior to carrying out any maintenance work.

 Avoid exposure to exhaust air.

Pneumatic  tool  exhaust  air  contains  oil  and 

contaminated moisture. Make sure the exhaust air is 

not directed towards your face or anyone else within 

the work area.

 Keep tool off electricity.

This pneumatic tool is not electrically insulated. To 

avoid a potential electric shock do not use where 

there is a possibility of coming into contact with live 

electricity.

CAUTION

 Handle tool carefully.

Abusive use of tool could invite failure or accident. 

Do not throw, drop or shock the tool.

 Handle air hose carefully.

Do not carry the tool by the air hose.

Do not pull the air hose to disconnect.

INSTRUCTIONS 

FOR

 THIS TOOL

About Your Tool

WARNING

 Wear protective glasses and a dustproof mask.

Operation generates chips and dust particles, etc. 

which may cause eye and / or respiratory injury: 

Always use PPE (Personal Protective Equipment) 

for eye and respiratory protection.

 Wear vibration reducing and shock absorbing 

gloves.

This is a power tool utilizing vibration. Wear vibration 

reducing and shock absorbing gloves. When your 

hands, fingers, arms, etc. feel discomfort during 

operations, immediately stop your work. Long hour 

operation should be prohibited, for it may cause 

Vibration-induced disorder.

 Always wear suitable hearing protection.

The tool generates loud noise. Always use ear plugs 

for hearing protection. Take necessary measures to 

comply with the local regulatory requirements and 

laws with regard to noise level, or do better.

 Do not operate tool at no Ioad.

Do not operate the tool at no load: It may not only 

Cause  damage  to  the  tool  but  also  may  cause 

Needles to fracture and fly out, possibly resulting in 

unexpected accident.

1. USAGE

 

Remove slag and spatter from welding.

 

Perform shot peening after welding. 

 

Remove rust, paint, cast sand from irregular metal 

surface.

 

Peel off adhered concrete. Clean brick surfaces and 

stone structures. 

 

The tool is used for operations in the difficult-to- 

operate areas where no other tool would be feasible : 

in narrow difficult-to-reach areas, extremely irregular 

surfaces, and grooves, cracks and other exterior 

surfaces without containers, etc.

2. CHECK THE CONTENTS OF THE PACKAGE

Check the contents and make sure that the tool does 

not have any damage which may have occurred 

during transportation. The contents should correspond 

to the list as follows. In case of damage/missing 

parts, please contact the sales agent from whom you 

purchased the tool.

JET CHISEL.indd   3

11.2.18   2:12:22 PM

Содержание AJC-16



















Отзывы: