6. HOW TO OPERATE THE TOOL
Warning
●
When sanding, always wear protective glasses
and respiratory protection: Microscopic dust and
DEUDVLYHSDUWLFOHVWKDWÁ\RIIWKHZRUNSLHFHPD\
cause eye or respiratory injury or both.
●
Before you change or adjust the tool or parts,
always disconnect the air supply hose.
●
Never touch the moving parts in operation.
6-1. Start and Stop (Fig. 7)
&KHFNWRVHHWKDWWKH7KURWWOH/HYHULVLQWKH2))
SRVLWLRQ
7KHQFRQQHFWWKHKRVHWRWKH%HOW6DQGHU
+ROGLQJWKH%HOW6DQGHU
D3XVKWKH/RFN/HYHUGRZQDQGEHKLQG
E*UDVSWKH7KURWWOH/HYHU
7KH%HOW6DQGHUVWDUWVUXQQLQJ
: K H Q \ R X U H O H D V H W K H 7 K U R W W O H / H Y H U L W
DXWRPDWLFDOO\UHWXUQVWRWKH2))SRVLWLRQ
Lock Lever
Throttle Lever
Pull the lock lever
toward you
to unlock the throttle
lever.
OFF
ON
)LJ
6-2. Adjusting the Rotation Speed (Fig. 8)
7KH GHVLUHG QXPEHU RI URWDWLRQ EHWZHHQ PD[LPXP
5RWDWLRQ 6SHHG DQG PLQLPXP 5RWDWLRQ 6SHHG LV
REWDLQHG E\ WXUQLQJ WKH JURRYH RI 9DOYH FORFNZLVH RU
FRXQWHUFORFNZLVHZLWKVFUHZGULYHU
0D[LPXP5RWDWLRQ6SHHG
3RVLWLRQWKHJURRYHRI$GMXVW9DOYHKRUL]RQWDOWRPDLQ
ERG\
0LQLPXP5RWDWLRQ6SHHG
3RVLWLRQWKHJURRYHRI$GMXVW9DOYHYHUWLFDOPDLQERG\
Minimum
Maximum
Adjust Valve
)LJ
6-3. Tracking Adjustment (Fig. 9)
%&/%&/%&/$
/RRVHQ WKH +H[ 6RFNHW 6HW 6FUHZ ZLWK D +H[
6RFNHW6FUHZ.H\DVVKRZQLQ)LJDQGDGMXVW
WKH DGMXVWLQJ 6FUHZ VR DV WKH DEUDVLYH %HOW WR
UXQRQWKHFHQWHURI,GOH3XOOH\7LJH[
6RFNHW 6HW 6FUHZ ZLWK +H[ 6RFNHW 6FUHZ .H\
DIWHUWKHDGMXVWPHQW
<RX QHHG QRW PDNH WKLV WUDFNLQJ DGMXVWPHQW
ZKHQ\RXKDYHDQRSWLRQDOPPZLGH%UDFNHW
$VVHPEO\DSSOLFDEOHWR%&/RQO\
%&/
/RRVHQ WKH +H[ HDG &DS 6FUHZ )LJ
ZLWKD+H[6RFNHW6FUHZ.H\
H[HDG&DS6FUHZFORFNZLVH
RU FRXQWHUFORFNZLVH ZLWK WKH DFFHVVRU\ +H[
6RFNHW6FUHZ.H\LQRUGHUWRPDNHWKHDEUDVLYH
EHOWUXQRQWKHFHQWHURIWKHLGOHSXOOH\
Hex. Socket
Set Screw
Adjusting Screw
Hex. Socket Set Screw
Adjusting Screw
Loosen
Adjust
Tighten
Adjust
Loosen
Adjust
Tighten
Adjust
B-10CL
B-20CL, B-20CL-A
Belt movement
when turned
clockwise
Hex. Socket Head
Cap Screw
Belt movement
when turned
counterclockwise
Clockwise
turn
Counterclockwise
turn
B-30CL
)LJ
6-4. Sanding Operation
Warning
●
Do not press the Abrasive Belt too hard upon the
workpiece. If you do so, the Abrasive Belt may
break.
●
When using a non-woven Belt, do not use the
Offset Bracket. If you do so, the Belt may come
Off , causing personal injury.
)RU GHEXUULQJ RSHUDWLRQ DQ 2IIVHW %UDFNHW RSWLRQDO
LVWREHXVHG
,Q WKLV DSSOLFDWLRQ WKH$EUDVLYH %HOW ZLOO EH EURXJKW
LQWR OLJKW FRQWDFW ZLWK WKH ZRUNSLHFH VRPHZKHUH LQ
EHWZHHQWKH,GOH3XOOH\DQG2IIVHW%UDFNHW
