background image

 

DW1500110  Rev.K1 

Sep  18  2015 

16

 

Section 10 

 WARRANTIES 

9.1  Nittan warrants to the customers that: 

(a) 

all products supplied hereunder will be of merchantable quality and will comply with any specification agreed 
between Nittan and customer. 

(b) 

it is not aware of any rights of any third party in the market which would or might render the sale of the products, 
or the use of any of the trade marks on or in products, or the use of any of the trade marks on or in relation to 
the products, unlawful. 

9.2  In the event of any breach of the Nittan's warranty in Clause 12.1(a) whether by reason of defective materials, 

production faults or otherwise, Nittan's liability shall be limited to: 

(a) 

replacement of the products in question; or 

(b) 

at the Nittan’s option, repayment of the price where this had been paid.

 

And the warranty period is three (3) years from the shipment from 

Nittan’s factory.

 

9.3  Notwithstanding anything to the contrary in this warranty terms, Nittan shall not be liable to the customer by reason 

of any representation or implied warranty, condition or other term or any duty at common law, or under the express 
terms of this warranty terms, for any consequential loss or damage whether for loss of profit or otherwise and 
whether occasioned by the negligence of Nittan or its employees or agents or otherwise, arising out of or in 

connection with any act or omission of Nittan relating to Nittan or supply of the products, their use by any customer. 

9.4  Customer shall indemnify Nittan against all loss, damages, liabilities, costs and expenses which Nittan may suffer 

or incur as a result of or in connection with any breach by customer of this warranties terms or any laws or 

regulations of any jurisdiction or any rules of any governing authorities. 

 

Содержание EVCA-P

















Отзывы: