background image

- 5 - 

CAUTION 

 

 

Exercise care not to pinch your hands between the top cover and control 
box or the upper and lower heat plates. 

Failure to do this may cause injury. 

 
 
 
 
 
 
 
 

  Avoid inserting your hands into the opening (part with a wire net) on the 

front face of the press. 

Failure to do this may cause burn. 

 
 
 
 
 
 
 
 
 
 

  Avoid using this machine outdoors. 

This product is not intended for the use outdoors. 

 

  Avoid dropping this machine or giving a strong shock. 

Failure to do this may cause fire or electric shock. 

 

  Take a measure to prevent this machine from dropping or falling, or do 

not install or operate the press at an unstable place. 

Failure to do this may cause injury, fire or electric shock. 

 

  Carry out the inspection described on page 18 of this manual before 

operating this machine. 

Failure to do this may cause fire or electric shock. 

 

  Do not use this machine for the endless splicing of belt of other 

manufacturers.

 

Endless splicing may become imperfect if this machine is used for the endless 
splicing of belt of other manufacturers. 
This may spoil the full functioning and performance of the belt. 

 
 
 
 
 
 
 
 
 
 

CAUTION 

CAUTION 

CAUTION 

CAUTION 

CAUTION 

CAUTION 

CAUTION 

Содержание PolySprint NPS-1210A-1























Отзывы: