INSTALLING THE SYSTEM continued
Hardwire Kit
1. Access the battery compartment.
2. Connect the hardwire adapter to the battery by securing the
black wire to the negative terminal and the red wire
to the positive terminal.
3. Connect the hardwire cable to the hardwire adapter and run the
cable to the preferred location.
4. Use the 36” extension cable if the hardwire cable is not long
enough to reach the headlamp on the helmet.
Battery Placement
1. After attaching the headlamp to the mount, run the headlamp
and extension cable toward the back of the helmet.
2. Place the supplied cable clips in the desired location to secure
the cable to the helmet.
3. After connecting the battery to the headlamp place the battery
in a pocket or pack, or use the supplied Velcro straps to
attached the battery in the desired location.
OPERATION
Headlamp Control
1. With the headlamp connected to the battery or hardwire kit,
press and release the power button to turn the light on.
2. Cycle through the four brightness levels by pressing and
releasing the power button.
3. To access the flash modes, press and hold the power button
until the headlamp starts to flash.
4. Cycle through the three flash modes by pressing and releasing
the power button.
5. To turn the headlamp off, press and hold the power button for
approximately 2 seconds.
6. Always disconnect the battery from the headlamp when
transporting the light system to prevent accidentally turning
on the headlamp which may cause overheating and potential
damage from high heat or even a risk of fire.
DISCOVER THE NIGHT
Thank you for choosing the Pro 4200 MX from NiteRider
®
,
the innovator in technical lighting systems. The Pro 4200 MX
combines a high-powered headlamp with CREE
®
LEDs
and a Li-ion battery.
To get the most from your NiteRider
®
light, we urge you to
familiarize yourself with the following operating and safety
instructions.
PARTS LIST AND IDENTIFICATION
Please verify the contents of your lighting system:
Pro 4200 MX Helmet Light Li-Ion
•
Pro 4200 MX Headlamp
•
8-cell Li-Ion Battery
•
Jawbone MX Helmet Mount
•
Hardwire Harness Kit (cable and adapter)
•
36” Extension Cable
•
48” Extension Cable
•
AC Adapter
Pro 4200 MX Hardwire
•
Pro 4200 MX Headlamp
•
Jawbone MX Helmet Mount
•
Hardwire Harness Kit (cable and adapter)
•
36” Extension Cable
INSTALLING THE SYSTEM
Jawbone MX Mount
1. Loosen the thumbscrew enough to allow the mount to fit over
the face guard.
2. Attach the mount to the preferred side of the face guard,
with the thumbscrew facing down.
3. Tighten the thumbscrew so that the mount is secure
and does not move excessively.
4. Insert the headlamp into the mount bracket from the rear
forward, making sure the release lever locks into place.
Then place the cable into the clip on the side
of the mount bracket.
5. To remove the headlamp, push the release lever
and slide the lamp backward out of the bracket.
Note: After mounting the headlamp, adjust it so the beam
illuminates the trail properly without distracting oncoming riders.
OPERATION continued
Fuel Gauge
The 8-step, LED Fuel Gauge is located on top of the headlamp
in front of the power button. When all four LEDs are lit solid green,
the battery is fully charged. As the battery discharges
⅛ increments of capacity, the LEDs from right to left,
successively go from solid green to blinking green, to out.
With only the final ⅛ capacity remaining one LED blinks red.
At this time, the headlamp should be turned off and the
battery recharged.
BATTERY CHARGING
BATTERY CHARGING AND CARE
1. Plug the AC Adapter into an electric outlet, then plug the cable
from the AC Adapter into the battery.
2. The LED indicator on the battery will turn red while the battery
is charging. When the battery is fully charged, the LED will
turn blue.
3. Unplug the AC Adapter from the battery by grasping the
connectors rather than the cable.
4. Always store your battery away with a FULL charge.
For extended periods, charge the battery every three months
to maximize its lifespan.
RUN TIMES
Low
6:00h
1000 Lumens
Med
3:30h
2000 Lumens
High
1:30h
4200 Lumens
Flash
16:30h 1400 Lumens
Beacon 16:30h 1400 Lumens
S.O.S. 16:30h 1400 Lumens
Race
16:30h 600 Lumens
*Run times are approximations and will vary.
**Race mode is intended for endurance races.
Thumbscrew
