Nilfisk-Advance SW 5070 B Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 35

background image

22

S31NUK5080(2)2001-01

BATTERY CONTROL AND RECHARGE

Please perform a periodical control of the elec-

trolyte level inside the battery. Lift the bonnet

and open the cells caps. If necessary, fill up

the cells with distilled water.
The electrolyte level has to be roughly 10 ÷ 15

mm over the electrode.

MAINTENANCE

(battery version)

After filling up, close the cells with the caps and

clean the upper surface of the battery.

Warning: Be extremely careful! The batterys

liquid is corrosive. If it comes in contact with

the skin or the eyes, wash repeatedly with

water and consult a doctor.

When necessary, recharge the battery in com-

pliance with the following instructions:
- turn off the machine by means of the main key;

- lift the bonnet;

- disconnect the connector of the battery

from the machine;

- recharge has to be performed in a properly

ventilated area;

- open all caps of the cells (or elements) of the

battery;

- connect the battery connector to the battery

charger;

- connect the battery charger to the mains (the

mains voltage level and the frequency have

to match the corresponding levels that are

applicable for the battery charger).

«
...
22
23
24
25
26
...
»

Содержание SW 5070 B




































Отзывы:

Нет отзывов

Похожие инструкции для SW 5070 B

GBC Proclick Pronto

Бренд: GBC Страницы: 16

Бренд: GBC Страницы: 74

Бренд: GBC Страницы: 28

Бренд: Duerkopp Adler Страницы: 80

1002556 - 1020 Power Eagle

Бренд: Nobles Страницы: 55

Memory Craft 5500

Бренд: Janome Страницы: 83

Бренд: Encore Страницы: 28

Autopax PAX200H

Бренд: Quasar Страницы: 76

Бренд: Nobles Страницы: 1

PREDATOR CXC100

Бренд: NSS Страницы: 8

HORIZON Memory Craft 9480 QC PROFESSIONAL

Бренд: Janome Страницы: 164

Бренд: JUKI Страницы: 72

Бренд: JUKI Страницы: 40

Бренд: Brother Страницы: 2

Бренд: Brother Страницы: 80

Бренд: Brother Страницы: 141

Бренд: Brother Страницы: 37

Бренд: Brother Страницы: 113

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды