FORM NO. 56041444 / SELECTSCRUB KA-27, KA-33, KA-39 - 2
Noise Level:
Controls:
Traction Motor:
Vacuum Motor:
Brush Motors:
Traction Drive:
Brushes:
Scrubbing Width:
Brush Pressure
Floating:
Strip:
Tanks
Solution:
Recovery:
Material:
Batteries:
Squeegee:
Wheels
Traction Wheel:
Caster Wheels:
Solution Feed:
Vacuum Shut off Switch:
Frame:
Outer Shell:
SELECTSCRUB KA-27SS
73dB @ 10’
Light effort, PUSH/PULL dead man
lever for forward or reverse operation.
Instrument panel with rocker switches
and variable speed control knob. Easy
access squeegee lift lever with auto-
matic vacuum control.
24V, 3/4HP, 195 rpm, permanent mag-
net gear motor.
24V, 3-stage, by-pass type, tangential
discharge. Develops 67"H
2
O sealed
lift, and 67 CFM through a 1-1/2" ori-
fice.
Two 24V, 3/4HP, 195 rpm, permanent
magnet gear motor. Direct drive to
self-leveling brushes.
All electronic control variable speed
drive. Featuring dynamic braking for
easy control up and down ramps.
Dual 14" (35.6cm) dia., self-leveling,
counter-rotating, 195 rpm.
27" (68.6cm).
115 lbs. (52.2Kg)
180 lbs. (81.7Kg)
Maximum will vary depending upon
floor surface and pad or brush used.
Current limit of brush drive motor must
not be exceeded.
22 gallon (83.3L)
22 gallon (83.3L)
High-density, molded seamless linear
polyethylene.
Four (4) heavy-duty deep cycle type,
6V, 250 AH, series connected.
35.8" (90.9cm) wide swinger type with
welded-in vacuum tube, easily replace-
able gum rubber blades (reversible for
extended wear), accurate, pressure
and tilt adjustments. Pivot makes
squeegee self-leveling on turns.
One (1) 10" (25.4cm) dia. molded.
Two (2) 5" (12.7cm) polyurethane swiv-
els with 750 lbs. capacity.
Two-speed solution pump and sole-
noid valve controls the flow rate to
center of each brush.
Float Switch
All welded steel 7 Ga. and 11 Ga. with
epoxy powder coating.
High-density molded polyethylene
tanks and covers.
SELECTSCRUB KA-33SS
73dB @ 10’
Light effort, PUSH/PULL dead man le-
ver for forward or reverse operation.
Instrument panel with rocker switches
and variable speed control knob. Easy
access squeegee lift lever with auto-
matic vacuum control.
36V, 3/4HP, 195 rpm, permanent mag-
net gear motor.
36V, 3-stage, by-pass type, tangential
discharge. Develops 74"H
2
O sealed lift,
and 72 CFM through a 1-1/2" orifice.
Two 36V, 3/4HP, 195 rpm, permanent
magnet gear motor. Direct drive to self-
leveling brushes.
All electronic control variable speed
drive. Featuring dynamic braking for
easy control up and down ramps.
Dual 17" (43.2cm) dia., self-leveling,
counter-rotating, 195 rpm.
33" (83.8cm).
125 lbs. (56.7Kg)
200 lbs. (90.7Kg)
Maximum will vary depending upon floor
surface and pad or brush used. Current
limit of brush drive motor must not be
exceeded.
30 gallon (113.6L)
30 gallon (113.6L)
High-density, molded seamless linear
polyethylene.
Six (6) heavy-duty deep cycle type, 6V,
200 AH, series connected.
41.5" (105.4cm) wide swinger type with
welded-in vacuum tube, easily replace-
able gum rubber blades (reversible for
extended wear), accurate, pressure and
tilt adjustments. Pivot makes squee-
gee self-leveling on turns.
One (1) 10" (25.4cm) dia. molded.
Two (2) 5" (12.7cm) polyurethane swiv-
els with 750 lbs. capacity.
Two-speed solution pump and solenoid
valve controls the flow rate to center of
each brush.
Float Switch
All welded steel 7 Ga. and 11 Ga. with
epoxy powder coating.
High-density molded polyethylene tanks
and covers.
SELECTSCRUB KA-39SS
73dB @ 10’
Light effort, PUSH/PULL dead man
lever for forward or reverse operation.
Instrument panel with rocker switches
and variable speed control knob. Easy
access squeegee lift lever with auto-
matic vacuum control.
36V, 3/4HP, 195 rpm, permanent mag-
net gear motor.
36V, 3-stage, by-pass type, tangential
discharge. Develops 74"H
2
O sealed
lift, and 72 CFM through a 1-1/2" ori-
fice.
Two 36V, 1 HP, 195 rpm, permanent
magnet gear motor. Direct drive to
self-leveling brushes.
All electronic control variable speed
drive. Featuring dynamic braking for
easy control up and down ramps.
Dual 20" (50.8 cm) dia., self-leveling,
counter-rotating, 195 rpm.
39" (99.1 cm).
135 lbs. (61.2 Kg)
200 lbs. (90.7Kg)
Maximum will vary depending upon
floor surface and pad or brush used.
Current limit of brush drive motor must
not be exceeded.
30 gallon (113.6L)
30 gallon (113.6L)
High-density, molded seamless linear
polyethylene.
Six (6) heavy-duty deep cycle type,
6V, 250 AH, series connected.
47.5" (120.7cm) wide swinger type with
welded-in vacuum tube, easily replace-
able gum rubber blades (reversible for
extended wear), accurate, pressure
and tilt adjustments. Pivot makes
squeegee self-leveling on turns.
One (1) 10" (25.4cm) dia. molded.
Two (2) 5" (12.7cm) polyurethane swiv-
els with 750 lbs. capacity.
Two-speed solution pump and sole-
noid valve controls the flow rate to
center of each brush.
Float Switch
All welded steel 7 Ga. and 11 Ga. with
epoxy powder coating.
High-density molded polyethylene
tanks and covers.
MACHINE SPECIFICATIONS
