Nilfisk-Advance PS 333A, Руководство по эксплуатации

Страница: 12 / 54

12
UK
Safety precautions
Caution!
NOTE! To minimise the risk of fire, electric shock or
injury, please read the safety precautions and caution
text thoroughly before using the machine.
. This machine is designed exclusively for indoor use.
. Do not leave the machine connected to the mains
supply. Always pull out theplug before leaving the
machine unsupervised.
. This machine is not a toy. Do not let children or
unauthorised personnel play with it. Never leave a
machine unsupervised if it is connected to the mains.
. Follow the instructions carefully. Ser vice and repair
work may only by carried out by an authorised
service agent. Only use original spare parts or parts
recommended by the manufacturer. Do not attempt to
modify the machine yourself in any way.
. Do not use the machine if the plug or mains lead are
damaged. If the machine does not work correctly, if it
has been damaged, left outside or become wet, return
it to the service agent for repair.
. Never drag or lift the machine by the mains lead. Make
sure the lead does notget trapped in a doorway. The
lead must not be exposed to heat.
. Make sure the lead does not touch any moving parts of
the machine.
. Always unplug the machine by pulling out the plug. Do
not unplug it by pulling on the lead.
. Switch off the machine before unplugging it.
. Never use the machine in the presence of flammable or
volatile solvents or gases.
. Switch off the machine and unplug it before fitting or
removing accessories.
. The machine is equipped with a “dead manʼs handle”
for the safety of the operator. Do not attempt to
override this safety mechanism or render it inoperable.
Do not fit any device to lock the switch in the on
position.
. The machine is earthed and should therefore only be
connected to an earthed mains socket.
. Caution! Do not run over the lead.
Keep these instructions for future
reference
Instruction for use
1 Components of the handle
1 Lever for handle height adjustment.
2 On/Off switch (dead manʼs handle type).
3 Safety lock for the on/off switch.
4 Hook for mains lead.
5 Upper and lower holder for solution tank.
6 Fluid control lever (when tank is fitted).
2 Rating plate
Before using the machine check that the voltage and
frequency of the mains supply match the values shown
on the rating plate. The rating plate is located on the
rear side of the motorhousing.
3 Solution tank
To be used for scrubbing and carpet schampooing.
Assembly:
a) Loosen the screws on the rear side of the upper
holder, pos.5 on figure 1. Pull it a bit uppwards along
the handle tube. There is a tounge on top and in the
bottom of the tank. Fit the bottom tounge into the lower
holder.
b) Fit the chain to the hook on the bottom of the fluid
control lever, figure 1 pos. 6. The chain should be
slightly tensed.
NOTE! Make sure you get the right tension on the chain.
If the chain is to tensed the fluid valve will continuosly
drain the solution from the tank. It can be neccessary
to loosen the lower tank holder as well to get the right
tension on the chain.
Press down the upper holder and fit the tounge on top
of the tank into the holder. Lock the holder in place by
fastening the screws on the rear side of the holder.
c) Connect the cleaning solution hose to one of the feed
holes located on eather side of the motorhousing.
d) If cleaning agent is used, follow the manufactures
dosing instruction.
The tank is filled through the big opening on top of the
tank.
4 Handle adjustment
Press the lever uppwards and lower the handle to
a comfortable working position. Lock the handle in
desired position by releasing the lever.
5a Mounting the pad holder
Unplug the machine before pad holder or brush is
mounted. Tilt the machine backwards, with the handle
in its upright position until the handle is resting on
the floor. Fit the hole in the pad holders centre on
to the drive mechanism, lock in place by turning it
anticlockwise. Check that the pad holder is locked in
place before starting the machine.
b Mounting the pad
Mount the pad holder as in earlier instruction. Press the
pad onto the holder, make sure the pad is centered.
c Mounting the brush
The brush is mounted the same way as the pad holder,
see earlier instruction.
d Dismounting the brush/ padholder
Unplug the machine. Turn the pad holder/brush,
clockwise to dismount.
Start and operation
Always choose a suitable pad or brush for the cleaning
task assigned. Adjust the handle to a comfortable
working position. Keep in mind that the pad/ brush
should be parallel with the floor. Press the safety lock
on the left or right side of the handle, then press the
on/ off switch on the same side. The machine starts
immediatly. When the machine starts the handle can
turn from the left to the right, this will stop as soon
as the pad/brush is working parallel with the floor. To
make the machine move to the right raise the handle
slightly, to make the machine move to the left lover
it slightly. If it feels like the machine is moving to
fast or to much in any direction, simply release the
on/off switch and the machine will stop immediatly.
Some practice may be needed in order to learn how
the machine works. Never allow the machine to run
on the same spot for longer than 5 seconds as this