manualshive.com logo in svg

Nilfisk-Advance ATTIX 19 GALLON AE, Инструкция по эксплуатации, Страница: 16 / 18

Поделиться
Скачать
Nilfisk-Advance ATTIX 19 GALLON AE Скачать руководство пользователя страница 16

17

1) 

Option depending on model

Original Instruction Manual

8  Troubleshooting

7

8.  Clean the level hose (7).
9.  Fit a new filter element.
10. Fit  the  filter  holder.  Ensure 

that  it  is  in  the  correct  posi-
tion.

11. Fit bar and close bar handle.
12. Dispose of the used filter ele-

ment  in  accordance  with  le-
gal regulations.

Never use the vacuum cleaner 
without a filter.

Fault

Cause

Remedy

‡ Motor does not start

> Fuse of the mains socket has 

blown.

• Connect mains fuse.

> Overload  protection  switch 

has tripped.

• Switch off the vacuum cleaner 

and allow it to cool for approx. 
5  minutes.  If  the  cleaner  can-
not  be  started  again,  contact 
the Nilfisk service department.

> Self-acting  carbon  brush  is 

worn

1)

• Have carbon brushes changed 

by Nilfisk Service.

‡ Motor does not run in auto-

matic mode

> Power  tool/pneumatic  tool  is 

defective  or  not  connected 
properly.

• Check  that  the  power  tool 

works or that the plug is insert-
ed correctly.

> The power rating of the elec-

trical tool is too low.

• Note that minimum power rat-

ing is P>40W

‡ Reduced suction power

> Suction  power  selected  with 

suction  power  control  is  too 
low.

• Set  suction  power  in  accord-

ance  with  section  4.2.3.  „Set-
ting suction power“.

> Clogged suction hose/nozzle. • Clean suction hose/nozzle
> Filter bag is full.

• See  section  7.2.2  „Replacing 

filter bag“.

> Filter element is clogged.

• See section 4.5 „Cleaning filter 

element“ and 7.2.5+7.2.6 „Re-
placing filter element“.

> Automatic Filter Cleaning Sys-

tem only:
Defective  cleaning  mecha-
nism

• Contact Nilfisk Service

‡ No  suction  power  during 

wet cleaning

> Tank is full. (Float has closed 

the suction opening).

• Switch  off  the  cleaner.  Empty 

the tank.

‡ The vacuum cleaner switch-

es off during wet cleaning

> Tank is full.

• Switch  off  the  cleaner.  Empty 

the tank.

‡ Voltage fluctuations

> Impedance of power supply is 

too high.

• Connect the cleaner to another 

socket  closer  to  the  fuse  box. 
Voltage  fluctuations  over  7% 
should not occur if the imped-
ance  at  the  transfer  point  is 



0.15 



.

Содержание ATTIX 19 GALLON AE



















Отзывы:

Нет отзывов