ELECTRICAL SYSTEM
FORM NO. 56043089 / AquaRide
™
/ BRX 700 - 67
Turning Fault Detection On or Off:
FACTORY DEFAULT: ON
Normally, the main control unit will perform checks of the electrical system during operation. If a fault occurs in a particular system that system
(and possibly others) will be shut down. This can make troubleshooting the system diffi cult. This option will allow service personnel to disable
some of the fault detection checks to facilitate troubleshooting. This will not disable the over-current protection on any of the systems. To turn the
fault checking on or off:
1 Turn
the
main power key switch to the off position.
2 Press and hold the scrub system off switch and the solution switch.
3 While holding both switches turn the main power key switch to the on position.
4 Continue to hold both switches until the solution indicator is yellow.
5 Release both switches. The status display will now indicate “E” or “d”.
6 Pressing and releasing the solution switch will now select between “E” for enabled or “d” for disabled. Enabled means that the fault checking
is turned on, disabled means that the fault checking is turned off.
7 To save the new setting turn the main power key switch to the off position.
8 The new setting will be saved and will remain in effect until it is changed again.
Turning the High Speed Scrub Option On or Off:
FACTORY DEFAULT: ON
The control system on the AquaRide is programmed to limit the maximum speed while scrubbing to a value less than that allowed for driving when
not scrubbing. The speed select switch on the control panel will override this speed limit feature and allow scrubbing at a higher rate of speed. If it is
desired to prevent scrubbing at this faster speed the fast/slow feature can be turned off. To turn this feature on or off perform the following steps:
1 Turn
the
main power key switch to the off position.
2 Press and hold the fast/slow switch.
3 While holding the fast/slow switch turn the main power key switch to the on position.
4 Continue to hold the fast/slow switch until the fast/slow indicator is green.
5 Release the fast/slow switch. The status display will now indicate “E” or “d”
6 Pressing and releasing the fast/slow switch will now select between “E” for enabled or “d” for disabled. Enabled means that the high speed
scrub feature is turned on, disabled means that the high speed scrub feature is turned off.
7 To save the new setting, turn the main power key switch to the off position.
8 The new setting will be saved and will remain in effect until it is changed again.
Scrub Deck Motor Type Selection:
FACTORY DEFAULT: MODE = E (EXTRACTOR), MOTOR TYPE: 1 IF EXTRACT ONLY DECK, 2 IF SWEEP EXTRACT DECK.
The AquaRide can be equipped with two different scrub deck options. This function confi gures the control unit current settings for each of the
scrub deck types. Improper setting of the motor type may result in motor damage due to overloading. To select the proper scrub deck motor
type:
1 Turn
the
main power key switch to the off position.
2 Press and hold the scrub system off and restore mode switches.
3 While holding both switches turn the main power key switch to the on position.
4 Continue to hold both switches until the restore mode indicator is yellow.
5 Release both switches. The status display will now indicate “S” or “E”.
6 Pressing and releasing the restore mode switch will now select between “S” for scrubber and “E” for extractor. Make sure that “E” is
displayed.
7 Press
the
scrub system off switch to save this setting
8 The status display will now display “1”, or “2”. Pressing the restore mode switch will now select between the two settings. Select “1” if the
machine is equipped with an extract-only deck. Select “2” if the machine is equipped with a sweep-extract deck.
9 Once the proper setting is displayed, press the scrub system off switch to save this setting.
10 The status display will now display “d” to indicate that the operation is done.
11 Turn
the
main power key switch to the off position.
SPECIAL PROGRAM OPTIONS (CONTINUED)
Содержание 56314019
