manualshive.com logo in svg

Nikon SMZ1500, Инструкция по эксплуатации

Поделиться
Скачать
Nikon SMZ1500 Скачать руководство пользователя страница 34

32

1

Photomicrographic magnification

Photomicrographic magnification = (PLI projection lens magnification)

×

 (Zoom magnification) 

×

 (Objective magnification)

•

When the P-ICI2 Coaxial Episcopic Illuminator is used:

Photomicrographic magnification = (PLI projection lens magnification)

×

 (Zoom magnification) 

×

 (Objective magnification) 

×

 1.5

•

When the Plan Apo and ED Plan series objective for SMZ1000/800 is used:

Photomicrographic magnification = (PLI projection lens magnification)

×

 (Zoom magnification) 

×

 (Objective magnification) 

×

 0.8

2

Attaching the beam splitter

Mount the beam splitter onto the zooming
body aligning the groove on the bottom of the
beam splitter with the positioning pin on the
zooming body while tilting the beam splitter
toward the rear.  Tighten the eyepiece tube
clamp screw.

[P-IBSS2]

Mount it so as to position the
port at either the left or right.

[P-IBSD2]

1) Mount it so as to position the

rear port at the rear.

2) Attach the side port to the

beam splitter main body with
the positioning pin on the
side port fitted into the
groove on the beam splitter
main body.  Tighten the side
port clamp screw.

CLICK

Groove

Pin

P-IBSS2  Port location

P-IBSD2  Attaching side port

Side port

Pin

Groove

Содержание SMZ1500






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды