manualshive.com logo in svg

Nikon SMZ1500, Инструкция по эксплуатации

Поделиться
Скачать
Nikon SMZ1500 Скачать руководство пользователя страница 30

28

4

Lighting area adjustment [G-LS]

It is possible to adjust the lighting area by moving the lamp socket back
and forth.  Adjust the lighting area to allow easy viewing.

5

Attaching filters [C-DSLS]

Rotate and remove the filter cap at the end of
the lamp house and insert a filter.  Use filters
that have a diameter of 33 mm and a width of
1.5 to 2 mm.

2

P-ICI2 Coaxial Episcopic Illuminator

Magnification of the P-ICI2 Coaxial Episcopic Illuminator is 1.5X.  Total
magnification is obtained by multiplying 1.5 by the total magnification of
the basic set of the microscope.

Note) Usable magnification for the P-ICI2

Coaxial Episcopic Illuminator is
restricted.  Use the magnification
within the range shown in the right
table.  If the magnification out of the
specified range is used, uneven

Objective

Zooming

magnification

HR Plan Apo 0.5X

2.5X or higher

HR Plan Apo 1X

2.5X or higher

HR Plan Apo 1.6X

Not usable

Fiber illuminator

Light guide

Luminous section

Main body

Eyepiece tube 
clamp screw

Incident section

Light guide clamp screw

Light guide mount

Fiber illuminator (C-FI115 for 
100/120V region and C-FI230 
for 230V region) available on 
order is necessary for the 
light source.
Read also the Instruction 
Manual of the Fiber 
Illuminator C-FI115/C-FI230.

Filter

ø33 mm

Filter cap

Содержание SMZ1500






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды