Nikon NPL-302 Series Скачать руководство пользователя | Manualshive

Страница: 8 / 234

background image

Safety

viii

Pulse Laser Station NPL-302 Series Instruction Manual

Warnings and Cautions

The following conventions are used to indicate safety instructions:

C

Warning –

Warnings alert you to situations that could cause death or serious

injury.

C

Caution –

Cautions alert you to situations that could cause injury or property

damage.

Always read and follow the instructions carefully.

Warnings

Before using the instrument, read the following warnings and follow the
instructions that they provide:

C

Warning –

Never look at the sun through the telescope. If you do, you may

damage or lose your eyesight.

C

Warning –

NPL-302 series instruments are not designed to be

explosion-proof. Do not use the instrument in coal mines, in areas
contaminated with coal dust, or near other flammable substances.

C

Warning –

The NPL-302 series instrument is a Class 1 laser instrument. The

laser beam is hazardous to the eyes and the body. Do not sight the instrument
on the face or body of a person. If you suspect an injury caused by exposure
to the laser beam, seek medical advice immediately.
If the instrument housing is open and the instrument is turned on, the laser
emits a beam stronger than the Class 1 safety level.

C

Warning –

Never disassemble, modify, or repair the instrument yourself. If

you do, you may receive electric shocks or burns, or the instrument may catch
fire. You may also impair the accuracy of the instrument.

«
...
6
7
8
9
10
...
»

Содержание NPL-302 Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NPL-302 Series

TUNICS T100S-HP

Бренд: Yenista Optics Страницы: 66

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 16

Бренд: MadMan Страницы: 37

Бренд: MADDALENA Страницы: 5

Бренд: KROHNE Страницы: 34

Бренд: QUNDIS Страницы: 20

Бренд: R&S Страницы: 2

Бренд: Topcon Страницы: 62

Бренд: Burkert Страницы: 192

Бренд: Hanna Instruments Страницы: 2

Бренд: Toro Страницы: 60

Бренд: Sonel Страницы: 84

Бренд: Supertech agroline Страницы: 10

Бренд: Isspro Страницы: 2

AirCon Service Mini Identifier R-1234yf

Бренд: Waeco Страницы: 132

Бренд: Polimaster Страницы: 24

Бренд: Apogee Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды