Nikon HQA46480 Скачать руководство пользователя

Страница: 180 / 185

Error Messages

166

Total Station DTM-322 Instruction Manual

Job Manager

Cannot Assign

100.13

You have tried to set the current job as the control file.

Press any key to return to the previous screen. Then select a different job.

Can't Create

100.14

There is no space available to create a job or record a point.

Press any key to return to the Job Manager. Then use the

DEL

softkey to delete old

jobs.

Existing Job

100.15

You have entered an existing job name for a new job.

Press any key and then change the name for the new job.

MAX 32Jobs

100.16

You are trying to create a new job when the maximum number of jobs (32) is already
stored.

Press any key to return to the Job Manager. Then use the

DEL

softkey to delete old

jobs.

Programs

NO Stn Setup

100.17

You did not perform a station setup or BS check before entering the Programs
function.

WARNING –

Selecting

Continue

does not resume the last ST record. You should only use

the

Continue

option if you are sure that the previous ST coordinates and the current HA

orientation are correct. Otherwise, records in the Programs function may not be correct.

XY&Z coordinate are required

100.18

Three-dimensional coordinates are required in S-Plane function.

Press any key to return to the point input screen. Then enter a three-dimensional
point.

To ...

Press ...

go to the Stn Setup menu

[2]

or select

Stn Setup

return to the BMS

[ESC]

go to the Programs menu

[1]

or select

Continue

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды