Nikon AF-S VR Micro Nikkor 105mm/f2.8G Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 118

background image

JAA63051-R.3689.A

- A65 ･ AF-S VR MC 105/2.8G -

　・

Gamma and Shift Adjustment (Automatic control)

Adjust the inclination and control center position based on the position sensor output of the VR unit.

During the adjustment, the message appears to confirm the lens position of angle (0 or 90 degrees).
Therefore, set the lens to the position and click "OK" button.

　　

When "OK" is shown on the execution screen, point the cursor to "Next" button and click it.

　・

Electromagnetic Lock Center Position Adjustment (Automatic control)

　　

Adjust the electromagnetic lock center position.
During the adjustment, the message appears to confirm the lens position of angle (0 or 90 degrees).
Therefore, set the lens to the position and click "OK" button.

When "OK" is shown on the execution screen, point the cursor to "Next" button and click it.

The inspection mode starts automatically. When the following is displayed on the execution screen, point
the cursor to "Next" button and click it.

«
...
87
88
89
90
91
...
»

Содержание AF-S VR Micro Nikkor 105mm/f2.8G























































































































Отзывы:

Нет отзывов

Похожие инструкции для AF-S VR Micro Nikkor 105mm/f2.8G

Бренд: Samsung Страницы: 44

Бренд: IC Realtime Страницы: 10

Бренд: Abus Страницы: 6

Бренд: Abus Страницы: 88

Бренд: Abus Страницы: 119

Бренд: Zavio Страницы: 31

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 189

Бренд: Panasonic Страницы: 195

Бренд: Panasonic Страницы: 56

GigE Vision STC-CMB2MPOE

Бренд: Omron Страницы: 55

Бренд: Kompernass Страницы: 12

Бренд: EverFocus Страницы: 2

Бренд: Northern Страницы: 2

Бренд: ACTi Страницы: 16

Бренд: Vivitar Страницы: 2

Бренд: Vivitar Страницы: 70

DH-IPC-HF8242FP-FR

Бренд: Dahua Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды