Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 109

background image

- A50 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

Adjustment of F.F.D (flange-back focal distance)

※

When the suspected lens has been disassembled, be sure to make the following inspection and
adjustment.

For "∞ positioning" of the suspected lens, refer to "Software Manual of Lens adjustment for

Electrical Device".

Looking through the eyepiece of horizontal-type collimator, rotate the mirror micromotion-control

handle to adjust focus, then measure focus position at 28mm (WIDE-end), 105mm, and 300mm (TELE-
end). The focus position to be measured is the numeric number shown at the moment when the color of

cross lines changes from green to orange.

Focal length (f)

Standard (mm)

28mm

fm +0.05 to +0.13

105mm

fm -0.03 to +0.35

300mm

fm -0.20 to +0.50

If the measured values do not meet the standard, take the following step and make the readjustment.

Measure the values [A: WIDE-side (28mm) value, B: 105mm value, and C: TELE-side (300mm) value],

and input them into the software of lens adjustment for electrical device.

Based on the calculating results of the software of lens adjustment for electric device, adjust the

thickness of the below three washers [washer under 1st lens-G unit (#133: selected from A to I); washer
under 2nd lens-G unit (#80: selected from A to K); washer under mount (#79: selected from A to J)].

If the result is positive (plus), increase the thickness, while negative (minus), decrease it.

Washer under 1st lens-G unit (#133): Adjustment washer (

ref. Page A43

)

Washer under 2nd lens-G unit (#80): Adjustment washer (ref. Page A41)
Washer under mount (#79): Adjustment washer (ref. Page A36)

Caution: Put a thin washer between thick washers when assembled.

Use the washers in the limited range of the following:

Adjustment washer

Limited range of thickness (mm)

Washer under 1st lens-G unit (#133: selected from A to I)

fm 0.5 to 1.1

Washer under 2nd lens-G unit (#80: selected from A to K)

fm 0.1 to 0.7

Washer under mount (#79: selected from A to J)

fm 0.2 to 1.5

•

•

•

User ID:uncf8224

«
...
95
96
97
98
99
...
»

Содержание AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Отзывы:

Нет отзывов

Похожие инструкции для AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Бренд: Gator Страницы: 32

SKYRAIDER DS287

Бренд: MallinCam Страницы: 205

Бренд: Idis Страницы: 40

DS-2CD2723G2-IZS

Бренд: HIKVISION Страницы: 35

Бренд: Verint Страницы: 16

Бренд: Idis Страницы: 8

Бренд: Inter-m Страницы: 18

ZUIKO DIGITAL ED50mm f2.0 MACRO

Бренд: Olympus Страницы: 2

ThermalTronix TT-H-BFTC Series

Бренд: Intellisystem Страницы: 7

Бренд: Vista Страницы: 22

Бренд: Abus Страницы: 18

Бренд: Safe Fleet Страницы: 2

Бренд: Vip-Vision Страницы: 8

MEGApix DWC-MB45iALPRT

Бренд: Digital Watchdog Страницы: 84

Vizioncam Series

Бренд: TechNexion Страницы: 2

Бренд: Hitachi Kokusai Electric Страницы: 39

Бренд: Vivotek Страницы: 2

Бренд: Salora Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды