STEREO ZOOM MICROSCOPE
Thank you for purchasing the Stereo Zoom Microscope.
Please read this instruction manual thoroughly before use to insure proper operation and long service.
glass
※
Rear
Fuse
AC Power Input
Upper Light
Upper Light
●
This is a precision instrument
‒
Handle With Care. Use caution to avoid
shock or excessive forces on instrument when in use or transport.
●
Use and store in location with low humidity and stable temperatures.
Avoid locations with dust, direct sunlight, excessive heat, or high vibration.
●
Keep lens surface clean from dirt and fingerprints.
●
Clean the lens gently with lens cloth or soft cotton cloth.
●
Do not turn the left and right Zoom Controls in opposite directions; this
will damage the instrument.
●
Before use, install the halogen bulb following the procedure below.
●
Only use as directed. Improper use may cause accident or injury.
●
When not in use store with protective cover, in location that
has low moisture in order to prevent internal mold growth.
●
Lighting unit not certified for use outside of Japan.
①
Remove the bulb cover from the Upper Light by rotating as shown.
Use care not to drop or damage glass.
②
Insert the bulb into the 2-prong socket.
※
If not fully inserted, the bulb will not light but use care not to
force or damage bulb when inserting.
③
Replace the bulb cover and rotate to tighten
．
PART IDENTIFICATION & SETUP
NOTES
SAMPLE PLACEMENT
EYE WIDTH ADJUSTMENT
EYE CUP USE
FOCUS & DIOPTER ADJUSTMENT
FUSE REPLACEMENT
SPECIFICATIONS
HALOGEN BULB INSTALLATION
①
Place the sample in the center of the Stage Plate.
②
If required, use Stage Clips to hold sample in place.
Hold both sleeves in each hand and look through the Eyepieces. Adjust the
Sleeves to align the left and right field of view seen through the Eyepieces.
●
For use without eyeglasses
：
Hold Eyepiece and rotate the Diopter
Adjustment Ring to adjust diopter setting. Align the Eye cups to point
toward user and look through the Eyepiece with eyes brought close.
●
For use with eyeglasses
：
Remove Eye cups to use.
In case of fuse failure, it can be
replaced with a commercially
available 250V 2A fuse.
①
Rotate the Zoom Control for highest magnification.
②
Look through the right eyepiece with the right eye and adjust the focus
using the Focus Knob.
③
Rotate the Zoom Knob for lowest magnification.
④
Using the Right Diopter adjustment, adjust the focus if required.
⑤
Now rotate the Zoom Control back to highest magnification and check the focus.
Repeat steps
②〜④
to achieve the best focus accuracy.
⑥
Rotate the Zoom Control for highest magnification. Look through the left Eyepiece
with the left eye, and adjust focus using the Left Diopter Adjustment Ring.
CAUTION
Halogen
Bulb
Installation
Halogen
Bulb
Installation
＜
Bulb Installation
＞
Rated Voltage
Magnification
Objective Lens
Eyepiece Lens
Working Distance
Eyepiece Angle
Focus Adjustment
Stand
Stage Plate
Eye Width Adj. Range
Diopter Adj. Range
Illumination
Base
Weight
ON
OFF
Socket
Socket
Fig.1
Fig.1
Fig.1
Tighten
Loosen
Fig.2
Fig.2
Bright
０
OFF
Insert
Upper Light
(Epi-Illuminator)
(Transmitted)
Light Power Control
Base
Lower Light
Power Sw.
Lower Light
Focus knob
350
〜
470mm
（
Range
）
60mm
AC100V
50/60Hz
6.5
〜
45
×（
for 10
×
eyepiece
）
13
〜
90
×（
for 20
×
eyepiece
）
0.65
〜
4.5
×（
Zoom Ratio 1:7
）
WF10
×（
FOV = 20mm
）
・
WF20
×（
FOV = 10mm
）
95mm
45
°
Movable Body
Rack and Pinion Type
φ
95mm
×
2pcs
①
Ground Glass
②
black/white (plastic)
55
〜
75mm
±
5diopter
Epi-illuminator: 6V
・
15W
Halogen bulb
Transmitted: 5W
ring light
L245
×
W190
×
H60mm
approx.5.7kg
Eye Cup
Eyepiece
Sleeve
Diopter Adj. Ring
Zoom Control
Stage Plate
Stage Clip
Head
245mm
190mm
Niigata seiki Co., Ltd.
5-3-14, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-33-5522 Fax. : +81-256-33-5518
MAIL [email protected]
URL http://www.niigataseiki.co.jp
XTS2021
Model
No.
Instruction Manual
