background image

 SD Series 

Operating & Safety Instructions 

 

USA   03/12

 

35 

 

Emergency Controls 

5.1

 

GENERAL 

 

CHECKING THE OPERATION OF THE EMERGENCY CONTROLS EVERY DAY 

AND/OR BEFORE EACH SHIFT IS AN ESSENTIAL PART OF THE OPERATOR'S 

DUTIES 

The operator and all ground personnel must be thoroughly familiar with the location and operation of 
the EMERGENCY CONTROLS. 

 

5.2 

IN THE EVENT OF AN INCAPACITATED OPERATOR 

Turn the key switch selector at ground  control station to ground (i.e. fully down). Lower on ground 
controls as detailed under section 4.3 Ground control operation.  If  initial  movement of the machine 
allows the master alarm to reset, normal controls will be available. This is then the fastest method of 
lowering the basket to the ground. 

 

5.3 

IN THE EVENT OF MACHINE FAILURE 

Operate manual hand pump (located adjacent to the base controls) and lower basket  to the ground 

using either basket  or base controls.  If  initial  movement of the machine allows  the master alarm to 

reset, normal controls will be available. This is then the fastest method of lowering the basket to the 

ground. 

 

 

FOLLOWING AN EMERGENCY DESCENT RECOVERY OF THE NIFTYLIFT, FULLY 
EXTEND AND RETRACT ALL CYLINDERS FROM GROUND CONTROL STATION 
BEFORE USING THE MACHINE. 

 

 
 

5.4

 

INCIDENT NOTIFICATION 

It is a mandatory requirement that any accident or incident involving a Niftylift, regardless of whether 
any party received injury or property was damaged, be reported by telephone directly to Niftylift.  
Failure to do so may render any warranty on the machine void. 

 

Содержание P21330









































Отзывы: