background image

4

Nieco Corporation - ExVection Toaster 6220

WARNING:  Keep cord clear of the working area.  Position the electric cord so that it will not get caught on other

equipment or interfere in work space.  Failure to do so can result in serious personal injury.

WARNING:  Check cords before each use.  If damaged, replace immediately.  Never use equipment with a dam-

aged cord since touching the damaged area could cause electrical shock resulting in serious injury.

SITE PREPARATION and INSTALLATION

This equipment is built to comply with applicable standards for manufacturers, including approval agencies, such as ETL.  Many local

codes exist, and it is the responsibility of the owner and installer to comply with these codes.

Check the electrical rating label to ensure that the equipment is connected to the correct voltage, phase, amperage and wattage that

are stated on the equipment’s identification label.  The identification label is located on the back plate of the equipment.  A secondary

label is included inside the equipment’s back plate.  This equipment should be connected to a power supply that is 208-240 volts, 60

Hz, AC only.  Do not operate on direct current (DC).  A substantial voltage drop will cause a loss of power and may damage the equip-

ment.  If the equipment does not operate when plugged into an outlet, check the power supply.

Observe all clearance requirements to provide air supply for proper operation, as well as sufficient clearance for servicing. Keep the

area around the equipment free and clear of combustibles. Dimensions and clearance specifications are shown under “Specifications

for ExVection Toaster 6220” and “Clearances Requirements for ExVection Toaster 6220”.

WARNING: The installation and connection must comply with national and local electrical codes.  Ensure electrical

supply conforms with electrical characteristics shown on the identification label. All services must be performed by a

qualified technician. 

IMPORTANT

The Nieco Corporation reserves the right to change specifications and product design. Such revisions do not

entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased

equipment.

OPERATING SAFETY

Toaster hot surfaces.  Do not touch hot surfaces of operating toaster that can cause serious burn injuries.

WORK AREA

Keep work area clean and well lit.  Cluttered or dark areas can increase the likelihood of accidents.

Do not set liquids on or near equipment.  Liquids entering equipment will increase the risk of electric shock.

Do not cover equipment or stack other objects on top of equipment.  Unattended items on equipment can increase the risk of

fire.

Do not use equipment outdoors.  Outdoor conditions can increase the risk of electrical shock.

Do not place equipment on or near a hot gas or electric burner or in a heated oven.  This creates an increased risk of fire

and electric shock.   

Содержание ExVection 6220













Отзывы: