Nidec RESCUE Select Pro страница 6 Скачать руководство пользователя

Страница: 6 / 17

General Information

Materials Enclosed

RESCUE

Select Pro Motor

RESCUE

Select Pro Motor and Programming App Installation and Configuration Guide

RESCUE

Select Pro Wiring Harness

Voltage Change Connector (115V)

Motor Labels for recording a customized Motor ID

Initial Inspection

Check the RESCUE

Select Pro motor to verify the following:

The shaft spins freely by hand.

The nameplate information conforms to the specifications of the motor ordered.

The RESCUE

Select Pro may look visually different than the motor it is replacing. The external

appearance is not an exact replica of the motor it is replacing. However, when properly installed, the motor
will fit in the blower housing and function according to specifications.

Содержание RESCUE Select Pro


















Результаты поиска

Содержание RESCUE Select Pro

Отзывы:

Похожие инструкции для RESCUE Select Pro

Бренды по названию

Популярные бренды

Nidec RESCUE Select Pro, Руководство пользователя

Результаты поиска

Содержание RESCUE Select Pro

Отзывы:

Похожие инструкции для RESCUE Select Pro

Бренды по названию

Популярные бренды