Nidec-Shimpo FGS-220VC Скачать руководство пользователя страница 30

Страница: 30 / 36

- 24 -

6. Message of status and error

The low er limit was reached.

“PUSH LMT ” is bl inking.

If the status is abnor mal, m ov e the

low er limit switch pos ition.

The upper limit was reached.

“PULL LMT” is blink ing.

If the status is abnor mal, m ov e the

upper limi t s witch posi tion.

The over l oad of the mounted force gauge

occurred in push direction.

Confirm whether the for ce gauge
used is cor rect.

Check whether the measurement
is abnormal.

The over l oad of the mounted force gauge

occurred in pull direction.

Confirm whether the for ce gauge

used is cor rect.

Check whether the measurement
is abnormal.

The emergenc y stop was pushed.

Confirm that a pr oblem is not

found, then release the emergency

stop.

The motor or the driver of the motor was
abnor mal.

Turn off and wai t one minute, then

turn on.
Contact TEC HNIC AL SUPPO RT if

the alarm is not canceled.

The com munication error between the

controller and the motor driver in the stand
occurred.

Turn off and wai t one minute, then
turn on.

Contact to our technical support if

the error alarm is not canceled.

The read error of the memory in the stand
occurred.

Turn off and wai t one minute, then
turn on.

If the error is not canceled,
initi alize the parameter. Refer to

the

below

procedure

the

initi alization.

The w rite error of the memory i n the stand
occurred.

Turn off and wai t one minute, then
turn on.

If the error is not canceled,
initi alize the parameter. Refer to

the

below

procedure

the

initi alization.

The stand could not rec ogniz e the
mounted force gauge.

Check :
The parameters s etting of the force

gauge, the sequence of power on
and the cable.

If no problem, as k to our technical

support.



All manuals and user guides at all-guides.com

Содержание FGS-220VC





































Результаты поиска

Содержание FGS-220VC

Отзывы:

Бренды по названию

Популярные бренды

Nidec-Shimpo FGS-220VC, Руководство по эксплуатации

Результаты поиска

Содержание FGS-220VC

Отзывы:

Бренды по названию

Популярные бренды