www.nicolaudie.com
Sunlite Touch-sensitive Intelligent Control Keypad
Ref. STICK-KE1
© Nicolaudie-Sunlite 1989-2015. All rights reserved. We reserve the right without notice to amend the technical information and specifications.
ESA Pro Software (Windows) - Ti Multi-Zone
http://www.nicolaudie.com/en/esapro.htm
ESA2 Software (Windows/Mac) - Single Zone
http://www.nicolaudie.com/esa2.htm
Hardware Manager (Windows/Mac) - Firmware, clock..
http://www.dmxsoft.com/global/ftp/hardwaremanager.zip
http://www.dmxsoft.com/global/ftp/HardwareManager.dmg
http://www.nicolaudie.com/smartphone-tablet-apps.htm
Page 4
V 1.4
Example of relay :
FINDER Ref.
22.23.9.012.4000
P1 P2 P3 P4 ... GND
Make a cable using the 3 pins : TX, RX and G (GND)
Set the RS232 parameters to : 9600bds 8 bits, no Parity, 2 Stop bits
- To play a scene, send 3 bytes :
1 x 255
- To stop a scene, send 3 bytes :
2 x 255
- To pause a scene, send 3 bytes :
3 x 255
- To release a pause, send 3 bytes :
4 x 255
- To reset a scene, send 3 bytes :
5 x 255
The scene number (x) can be from 1 to 40. For instance, 11 means
Page B Scene #3
The controller can be connected to a local network, allowing it to be
controlled from a smartphone or tablet over WiFi.
• Connect the controller to a router or switch with an RJ45 cable
• The controller is set by default to get an IP address from the
router via DHCP. If the network is not working with DHCP, a
manual IP address and subnet mask can be set using the
Hardware Manager
• If the network has a filewall enabled, allow port 2430
The controller can be connected to an existing automation system
over a network and triggered via UDP packet on port 2430. Refer to
the remote protocol document for more information.
BLACKOUT Relay (energy saving)
Dry Contact Port Triggering
Network Control
UDP Triggering
The controller works with the official IR remote control, however there
is no receiver. A 36khz infra red receiver can be connected, such as
the TSOP34836 by Vishay Semiconductors. Farnell ref: 4913127. This
can be attached to the 20 pin connector. It’s a good idea to add a
resistor and capacitor to surpress power supply disturbance.
A relay can be connected between the RELAY and GND sockets
of the 20 pin extension socket. This can be used to turn off other
equipment such as lighting drivers. The signal is connected when
the controller is in standby.
Infra Red
RS232 Triggering
It is possible to start scenes using the input ports (contact closure).
To activate a port, a brief contact of atleast 1/25 second must be
established between the ports (1...8) and the ground (GND). Note:
the scene will not be switched off when the switch is released
.
Technical datasheet Revision date 20 Mar. 2015
The controller be programmed from a PC, Mac, Tablet or
Smartphone using the software available on our website.
Refer to the corresponding software manual for more
information. The firmware can be updated using the
Hardware Manager which is included with the programming
software.
Programming the Controller
Setting up the Controller
The controller can be used with one of 3 different apps. Each
available at Google Play and the App store.
STICK Remote
Designed to work seamlessly with the controller, STICK
Remote provides an easy way to control your lights over a
local WiFi network. Use the slider to change the dimmer,
color or speed, and the 8 scene buttons to select scenes and
effects just like the wall panel.
Easy Remote
Create an entirely customized remote controller for your tablet
or smartphone. Easy Remote is a powerful and intuitive app
allowing you to easily add buttons, faders, color wheels and
more. Connect to a WiFi network and the app will find all
compatible devices.
Arcolis
The Arcolis application is a comprehensive tool allowing you
to directly control and re-program the controller from your
smartphone or tablet. This is a simple application which can
be used by just about everyone in any situation. Mobile, easy
to use and powerful, Arcolis is the ideal controller for dimming
or switching traditional, LED and RGB color mixing DMX
lighting fixtures. Program static and dynamic lighting scenes
and effects.
iPhone/iPad/Android Control
