English –
6
EN
3.5.2.B - Automatic programming of positions “0” and “1”
In some motors for roller shutters, with electronic limit switches, there is a procedure
that automatically detects positions “0” and “1”. If this feature is available, after TTPRO
switches on the LED on the button
AUTO
flashes.
To perform this procedure there must be present on the application the caps on ascent
and/or burglar springs on descent. For more details refer to the motor instructions.
01.
Press the button
AUTO
.
02.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
03.
The motor emits 2 beeps (= start of the procedure).
04.
The roller shutter must move up: if it goes down, immediately press the button
or
to reverse the direction of movement.
05.
At this point the procedure continues automatically: initially, TTPRO finds the
“0”
position, by the caps, on opening; it then finds position
“1”
, by the anti-intrusion
springs, on closing.
06.
The motor emits 3 beeps (= end of the procedure) and the roller shutter closes
fully.
07.
Lastly, press the
ON/OFF
button to display the new settings.
3.5.2 - PROGRAMMING OF POSITIONS
Motors with electronic limit switches have functions to programme the positions:
“0”
(rolling shutter or awning all rolled up),
“1”
(rolling shutter or awning all unrolled) and
“I”
(rolling shutter or awning in an intermediate position). If a position is already stored, the
corresponding LED will be lit, otherwise a short flash indicates that the position has not
been programmed.
3.5.2.A - Manual programming of positions “0”, “1” and “I”
The positions must be stored in the following order:
“0”
,
“1”
and
“I”
.
The memorisation procedure may vary depending on the type of motor used. Therefore,
refer to the technical specifications which are also available on www.niceforyou.com
site, with details and specific examples for each type of motor.
• Programming position “0”
01.
Use the
or
button to bring the roller shutter/awning to the “0” position
desired.
02.
Press the button
AUTO
: the LED on the button flashes.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
04.
When finished, the LED on the button
AUTO
turns on with a steady light.
Notes
• The direction of movement associated with the button may be not correct until
position
“1”
is stored. • In some types of motors, changing position
“0”
could erase
positions
“0”
and
“I”
.
• Programming position “1”
01.
Use the
or
button to bring the roller shutter/awning to the “1” position
desired.
02.
Press the button
AUTO
: the LED on the button flashes.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
04.
When finished, the LED on the button
AUTO
turns on with a steady light.
Note:
changing position
“1”
erases position
“I”
.
• Programming position “I”
01.
Use the
or
button to bring the roller shutter/awning to the intermediate
position “I” desired.
02.
Press the
AUTO
button: the LED on the button flashes.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
04.
When finished, the LED on the button
AUTO
turns on with a steady light.
Note:
you cannot store position
“I”
if the
“0”
and
“1”
positions have not been stored
previously.
3.5.3 - DELETING PRE-PROGRAMMED POSITIONS
• Deleting Position “0”
01.
Press the button
AUTO
: the LED on the button flashes.
02.
Press the button
RADIO
TEST
: the LED on the button flashes.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
04.
Once this operation terminates, the LED on the button
AUTO
flashes.
• Deleting Position “1”
01.
Press the button
AUTO
: the LED on the button flashes.
02.
Press the button
RADIO
TEST
: the LED on the button flashes.
03.
➔
The
green OK
LED flashes: (within 3 sec) press the
OK
button to confirm.
04.
Once this operation terminates, the LED on the button
AUTO
flashes.
