English –
4
EN
Adr 4
0 0 0 1 0 0 0 0 0
Adr 5
0 0 0 0 1 0 0 0 0
Adr 6
0 0 0 0 0 1 0 0 0
Adr 7
0 0 0 0 0 0 1 0 0
Adr 8
0 0 0 0 0 0 0 1 0
Adr 9
1 0 0 0 0 0 0 0 1
Adr 10
0 1 0 0 0 0 0 0 1
Adr 11
0 0 1 0 0 0 0 0 1
Adr 12
0 0 0 1 0 0 0 0 1
Adr 13
0 0 0 0 1 0 0 0 1
Adr 14
0 0 0 0 0 1 0 0 1
Adr 15
0 0 0 0 0 0 1 0 1
Adr 16
0 0 0 0 0 0 0 1 1
Adr > 16
0 0 0 0 0 0 0 0 1 flashing
If at the end of the search no motor is found, TTPRO emits 2 short beeps and
the
OK
LED turns steady
RED
.
3.3.2 - Motor search
A
If TTPRO is already on:
01.
Press and release the
ON/OFF
button (
1 long beep);
scanning of the TTBUS starts automatically.
B
If a motor is found, the
OK
LED turns
GREEN
and, the level LEDs indicate the
address of the motor found (decode the address with the help of Table 1).
If at the end of the search no motor is found, TTPRO emits 2 short beeps and
the
OK
LED turns steady
RED
.
C
02.
To search for another motor connected to the same BUS:
• if the motor has a higher address than the current one, press the
+
button;
•
if the motor has a lower address than the current one, press the
–
button.
If a motor is found, the
OK
LED turns
GREEN
and the level LEDs indicate the ad-
dress of the motor found (decode the address with the help of Table 1).
If at the end of the search no motor is found, TTPRO emits 2 short beeps and
the
OK
LED turns steady
RED
.
3.3.3 - Switching Off of TTPRO
01.
Press and hold the
ON/OFF
button for about 3 sec.
02.
Release the button when TTPRO emits 1 beep and the RED LED starts to
flash quickly.
• TTPRO turns off automatically after 1 minute of inactivity.
3.3 - ON/OFF button
SWITCHING ON/OFF AND MOTOR SEARCH
3.3.1 - Switching On of TTPRO
01.
Press and release the
ON/OFF
button (
1 long beep);
scanning of the TTBUS starts automatically, from address 0 to 255 (at this stage
the level LEDs are flashing alternately).
02.
If a motor is found, the
OK LED
becomes
GREEN
and, the level LEDs indicate
the address of the motor found (see Table 1).
TABLE 1
ADDRESS
1 2 3 4 5 6 7 8 A
Adr 0xFF
1 1 1 1 1 1 1 1 1
Adr 0
0 0 0 0 0 0 0 0 1
Adr 1
1 0 0 0 0 0 0 0 0
Adr 2
0 1 0 0 0 0 0 0 0
Adr 3
0 0 1 0 0 0 0 0 0
LED OF FUNCTION
DESCRIPTION
STEADY LIGHT
Function already present and already set.
LIGHT OFF
Function not present.
FLASHING LIGHT
Function already present but not yet set , or currently being set.
LED OF LEVEL
DESCRIPTION
This series of LEDs
can have different
meanings depend-
ing on the function
enabled
• RF noise level (V-METER)
• Motor Address
• Level
• Setting
CHARGE LED
DESCRIPTION
Usb
If the USB cable is connected
, the BLUE LED is on.
Chrg
If the USB cable is connected
, the GREEN LED flashes when
the battery is charging.
