Nice OXIBD Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 24

Nice OXIBD Скачать руководство пользователя страница 10

9

- English

EN

by the installer from the “List of commands” of the automation’s control unit.

Note

- A key can be associated

with only one output, while the same output can be associated with multiple keys.

PROCEDURE 2 - Mode 2 memorisation (and extended Mode 2)

01.

In the control unit manual:

choose the command to be memo-

rised and remember its “identification number”.

02.

On the receiver:

press and release key A for a number of times

matching the number that identifies the command chosen at

step 01: LED B will flash the same number of times.

1

2

x No. ....

=

...

03.

On the transmitter with the key to be memorised:

• If the transmitter is a one-way device:

(within 10 seconds) on the transmitter: hold down the key to be

memorised and release it once LED B (on the receiver) emits

the 1

st

of 3 green flashes (=memorisation completed correctly).

(*2)

• If the transmitter is a two-way device:

(within 10 seconds) on the transmitter: press and immediately

release the key to be memorised; LED B (on the receiver) will

flash green 3 times (=memorisation completed correctly).

(*2)

(*2) Note -

If there are other keys to be memorised (belonging to other transmitters) with the same com-

mand, repeat step 03 within the next 15 seconds for each further key to be memorised (the procedure

terminates once this time elapses).

3.3 - Memorising a new transmitter “near the receiver” - only for one-way transmitters

This procedure allows for memorising a new transmitter by means of a second functioning transmitter, already

memorised in the same control unit. This enables the new transmitter to receive the same settings as the

«
...
8
9
10
11
12
...
»

Содержание OXIBD

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды