Nice Era Plus L, Полное руководство

Страница: 15 / 128

English –
13
EN
5.16 - Adjustment of “Sun” climate sensor (ref. paragraph 6.2.3)
At the factory, the intervention threshold to is set at level 3 and to change it you must take the following steps.
Before starting the procedure, move the shutter/awning to the mid-point of its stroke.
01. Keep the
n
key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the
t
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Briefly press the
t
key a few times, depending on the level you want to set for the intervention threshold:
1 press = 5 Klux
2 presses = 10 Klux
3 presses = 15 Klux (factory setting) *
4 presses = 30 Klux
5 presses = 45 Klux
After about 10 seconds, the motor performs the number of movements indicated by the level number selected. Note – If this does not occur, cancel the proce-
dure. this way, the adjustment is completed without changing the factory setting.
04. Keep the
n
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
1 /
2 /
3 /
4 /
5 /
10
sec.
03
0,5
sec.
x 1 = 5 Klux
x 2 = 10 Klux
x 3 = 15 Klux ( * )
x 4 = 30 Klux
x 5 = 45 Klux
5
sec.
01 02
5
sec.
04
5
sec.
3 2
? 3
Note : • When performing the procedure, you can cancel it at any time by keeping the
n
and
t
keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements. • If you use a sensor equipped with a “trimmer”, you must read the sensor instructions and ad -
just the threshold directly on the sensor.
––– Procedure 5.16 ––– executable only with a series transmitter Era P and Era W
10
sec.
04
0,5
sec.
x 1 = 5 Klux
x 2 = 10 Klux
x 3 = 15 Klux (
*
)
x 4 = 30 Klux
x 5 = 45 Klux
5
sec.
01
1
sec.
PRG
02
1
sec.
PRG
03
2 2 3
05
1 /
2 /
3 /
4 /
5 /
5
sec.
? 3
(*) - Factory setting
5.17 - Adjustment of “Wind” climate sensor (ref. paragraph 6.2.3)
At the factory, the intervention threshold to is set at level 3 and to change it you must take the following steps.
Before starting the procedure, move the shutter/awning to the mid-point of its stroke.
01. Keep the
n
key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the
t
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Briefly press the
s
key a few times, depending on the level you want to set for wind threshold:
1 press
= wind at 5 Km/h
2 presses = wind at 10 Km/h
3 presses
= wind at 15 Km/h (factory settings)
*
4 presses = wind at 30 Km/h
5 presses
= wind at 45 Km/h
After about 10 seconds, the motor performs the number of movements indicated by the level number selected. Note – If this does not occur, cancel the proce-
dure. this way, the adjustment is completed without changing the factory setting.
04. Keep the
n
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.