Nice ALTO100C, Инструкции и предупреждения по установке и использованию

Страница: 4 / 35

3 – English
English
––– STEP 3 –––
CHECKS AND PROCEDURES PRIOR
TO INSTALLATION
3.1 - CHECKING SUITABILITY OF GATE TO BE AUTO-
MATED AND RELATIVE ENVIRONMENT
• Ensure that the mechanical structure of the gate complies with current
national standards and that it is suitable for automation. For this check,
QDEDQSNSGDHMENQL@SHNMRODBHjDCNMSGDF@SDC@S@OK@SD Important -
This “ALTO” system cannot be used to automate a gate that is not
@KQD@CXDEjBHDMS@MCR@EDETQSGDQLNQDHSB@MMNSRNKUDCDEDBSRB@TRDCAX
incorrect gate installation or poor maintenance.
• Ensure that the gate leafs move regularly and smoothly, by performing
the following test: manually move the leafs in both directions and ensure
that movement is free of friction throughout all points of travel (there
must be no points requiring a different level of force).
• Ensure that the gate leafs are perfectly balanced, by performing the
following test: manually move the leafs to any position; take away the
hands and ensure that the leafs remain stationary.
q (ESGDQDHR@jWDCNARS@BKDHMSGDYNMDNESGDBNKTLMVGDQDSGDFD@QLN -
tor is to be installed) it is important to check whether this will enable
complete arm rotation and therefore the maximum leaf opening angle.
For this check, refer to point 5 of paragraph 3.2.
• In the vicinity of the post where the gearmotor is to be installed, ensure
SG@SSGDQDHRRTEjBHDMSRO@BDSNODQENQLSGDL@MT@KFD@QLNSNQQDKD@RD
procedure.
• Ensure that the surfaces chosen for device installation are solid and can
FT@Q@MSDD@RS@AKDjWSTQD
• Ensure that all devices to be installed are in a sheltered location and
protected against the risk of accidental impact.
q $MRTQDSG@SSGD@QD@HRjSSDCVHSGkNNQLNTMSDCRSNORMNSRTOOKHDCSN
limit opening and closing.
3.2 - CHECKING THE PRODUCT APPLICATION LIMITS
1 - Suitability of the product for gate automation . For this check,
refer to Graph 1 as follows:
a) - measure the width of the gate leaf and determine its weight.
b) - note these two values in Graph 1 and check the point at which
the two values intersect:
•
if the point is located within area “A” = the gate can be auto-
mated using standard length arms (supplied as standard) or short
arms (the length of the arm is established during the phase prior to
installation - paragraph 3.4);
•
if the point is located within area “B” = the gate can be auto-
mated using standard length arms (supplied as standard);
•
if the point is located within area “C” = this product cannot be
used to automate the gate.
2 - Maximum leaf height . The “ALTO” system can automate leafs with
a height of up to 200 cm.
3 - Maximum leaf width . The “ALTO” system can automate leafs with a
width of up to 160 cm (see Graph 1 ).
Maximum leaf weight . The maximum weight of the leaf depends
on its length. To calculate the maximum admissible weight with the
“ALTO” system, proceed as follows:
a) - measure the width of the gate leaf and note the value in Graph 1 .
Starting from this value, trace a vertical line until it intersects with the
two traced lines.
b) SQ@BD@GNQHYNMS@KKHMDEQNLD@BGONHMSNEHMSDQRDBSHNMTMSHKSGDSVN
maximum admissible weights are shown (depending on the length of
the arm used to install the gearmotor: with standard length arms, the
weight may vary from 110 to 180 kg; with short arms, the weight may
vary from 100 to 150 kg).
5 - Gearmotor overall dimensions . On the basis of the overall dimen-
sions stated in ƄJ BGDBJSG@SSGDQDHRRTEjBHDMSRO@BDNMSGDKD@E
and post to enable gearmotor installation. In particular, ensure the
following:
• the width of the post must be greater than 80 mm (
ƄJ ). Caution!
– any lower widths would prevent installation of the gearmotor.
• the distance between the edge of the post (the side closest to the
GHMFDOHM@MC@MXjWDCNARS@BKDOQDRDMSADGHMCSGDONRSLTRSAD
greater than 120 mm ( ƄJ ). Caution! – any lower widths would
prevent installation of the gearmotor.
6 - Gearmotor positioning . Never install the gearmotor upside down
(see ƄJ ).
7 - Maximum leaf opening angle . If the gearmotor is installed with a
standard length arm (supplied as standard) a leaf opening angle of
110° is possible. Otherwise, if the short arm is used, the leaf opening
angle is reduced to 90°. The length of the arm is established during
the phase prior to installation - see paragraph 3.4.
8 - Mechanical stops . The gearmotors in the “ALTO” system do not
implement mechanical systems to limit leaf travel on closing or open-
ing. Therefore, to enable installation of the “ALTO” system, some
kNNQLNTMSDCRSNORNMNODMHMF@MCBKNRHMFLTRSADjSSDCSGDRD
stops are not supplied in the kit and are not part of the Nice Home
product range).
2 3
180
160
140
120
100
80
60
40
20
0,8
0
1 1,2 1,4 1,6 0,9 1,1 1,5 1,3
GRAPH 1
(see paragraph 3.2)
WIDTH (m)
WEIGHT (kg)
line of
maximum
leaf weight:
with stan-
dard arm
line of
maximum
leaf weight:
with short
arm
80 mm
minimum
120 mm
minimum
YES
NO