background image

26

26

LIMITED TWO-YEAR WARRANTY

Apollo  Gate  Operators  are  warranted  against  defects  for  a  period  of

24  months  from  the  date  of  purchase,  providing  recommended  installation
procedures  are  followed.  This  warranty  is  in  lieu  of  all  other  warranties
expressed  or  implied  (some  states  do  not  allow  limitations  on  how  long  an
implied warranty lasts, so this limitation may not apply to you) and shall be
considered  void  if  damage  was  due  to  improper  installation  or  use,
connection  to  improper  power  source,  or  if  damage  was  caused  by  fire,
flood,  or  lightning.  The  manufacturer  will  not  be  responsible  for  any  labor
charges incurred in the removal or replacement of defective parts.

In case of failure due to defective material or workmanship during the

warranty  period,  the  defective  part  will  be  repaired  or  replaced  at  the
manufacturer’s option at no charge if returned freight prepaid. New or factory
rebuilt replacements may be used. Replacement parts are warranted for the
remaining portion of the original warranty period. The manufacturer will pay
standard  ground  freight  back  to  the  customer  on  the  return  of  repaired  or
replaced items in warranty.

Lighting  or  electrical  power  surges  may  cause  damage  beyond  repair  and
are not covered in this warranty.

APOLLO

Gate Operators, Inc.

Содержание T5-ETL



























Отзывы: