nicai systems NIBO burger Скачать руководство пользователя страница 81

Страница: 81 / 97

Construction manual - Robot kit NIBO

burger

08.09.2015

Now we test the functionality of the

floor sensors / colour sensor bricks

Press once

button 1

Raise the robot and test the sensors analog to the IR sensor test.

LED 1

should glow for the

blue

sensor brick,

LED 2

and

LED 3

should glow

for the

green

sensor brick and

LED 4

should glow for the

red

sensor brick.

Now

switch off

the robot.

3.3 Part III – Motors & odometry sensors

Now

press and hold

button 2

and

switch on

the robot.

Then LED 2 must flash. Now loose the button! LED 2 flashes shortly and the
test program has been started.
We start with testing the

odometry sensors

. We want to verify that the

phototransistors are able to detect the

turns of the wheels

Now turn carefully (from the top side) the

left red gear

. While doing this

LED 1

and

LED 2

must flash alternate. If the photoelectric barrier is blocked

by the gear the red led flashes. If it is not blocked then the blue led flashes.
The right side has to be tested analog.

Now we test the motors. Press once button 2:

First we must connect jumper

. Now the robot is able to drive!

•

Press button 1 → the robot drives forward

•

Press button 2 → the robot stops

•

Press button 3 → the robot drives backward

It's possible that

NIBO

burger

will not drive in a straight line. That doesn't

matter for it is an unregulated drive!

Now the robot has to be

switched off

http://nibo.

nicai-systems.de

Содержание NIBO burger


































































































Результаты поиска

Содержание NIBO burger

Отзывы:

Бренды по названию

Популярные бренды

nicai systems NIBO burger, Руководство по монтажу

Результаты поиска

Содержание NIBO burger

Отзывы:

Бренды по названию

Популярные бренды